Connection of the Keenetic Giga router in a repiter mode. How to set up a zyxel router…

Setting up the Roters of the Zyxel Keenetic series as a Wi-Fi repiter, or amplifier, a little more complicated than other manufacturers. Let me remind you that the mode of the wireless repeater, or WDS bridge, allows you to repeat the signal from another Wi-Fi source and thereby extend the zone of its work. In this article, I will show how the Wi-Fi amplifier mode is adjusted on the morally obsolete Zyxel Keenetic Lite or 4G routers, and on updated models that are already produced under a separate Keenetic, Giga, Viva, Air, Ultra, Speedster Runner 4G and so on.

Quite often the capabilities of Wi-Fi router are not enough. For example, the wireless network in large rooms may not cover the entire coating area. Either the same signal due to reinforced concrete partitions and other obstacles can be very weak. As a result, it is quite difficult to use the capabilities of the local network and the Internet. It is necessary to somehow expand the coverage area of ​​an existing network and strengthen the signal from the router.

We set up Wi-Fi

Since the wireless network is used in most modern apartments and houses, it is worth paying special attention to using a wireless access point. It needs to be pre.created and configured. We open the section “Wi-Fi”. You will find this badge below the panel. Opposite the point “Turn on the access point” we put a checkmark in its absence. Now you need to come up with the name of the network and put the “WPA2-PSK” defense. It is also recommended to change the password. Come up and write down a reliable combination. The Wi-Fi setup takes a few minutes, so even a beginner can handle such a task. The Keenetic 4G 1210 Inte Wee is intuitive and simple, so usually difficulties with its settings do not arise.

However, do not be upset. In fact, any modern model of Wi-Fi router can function in a repiter mode (amplifier) ​​mode. Devices produced by ZYXEL (pronounced as a “Zabikel”, but the vernacular option. “zixel”) is not an exception. True, for this you will have to take an additional router and configure it in a special way. As a result, a Wi-Fi Repiter will be obtained, that is, a device that can connect to the existing wireless network and broadcast it further.

In this case, no new wireless network will appear. She will remain the same and even with the same name and, of course, with one password. If everything is done correctly, then devices (PC, laptops, tablets, smartphones, etc.) will be able to automatically switch from one router to another, focusing on where a stronger signal. What the user gets? Firstly, the radius of the Wi-Fi network is significantly increased. Secondly, the signal itself becomes stronger.

To make it more clear, consider how to configure Zyxel Keenetic 4G to work in a repiter or relay mode.

Alternative firmware

The manufacturer ZYXEL on different models in the basic configuration sets the software modules responsible for certain functions. In the purchased product, the function of the repiter (amplifier) ​​is sometimes not provided for. Refresh firmware, however, is available, downloading it from the Internet. If another mode is required, for example, an adapter, it requires another firmware of the device.

With some risk of gaping guarantee on the router, alternative firmware DD WRT of a third.party developer is set. It includes all the functions of Zyxel routers, a reipiter including. Often with a universal firmware, the device works more stable than on ZYXEL.

Download DD WRT from the official website of the developer in the form of an archive, extract a file from it with an extension.bin, save it on a computer. On the starting page of the ZYXEL router, we click “Settings” (gear symbol) in the lower row and switch to the “files” tab (“micro.oprogram”). In it, we click on the “review” stencil, find the downloaded file and execute the “Replace” command. To continue, we agree with the replacement by pressing the yes button. Indicators on the front panel of the Repite will report the end of the process.

Zyxel Keenetic Settings in Repeater mode

The regime of the repeater or repiter used to expand the zone of action of the Wi-Fi network of the main router in the ZYXEL settings menu is called the “amplifier”. But the name “Retransalator” more accurately characterizes the work of the device. When the repiter is located at the place of sufficient signal force of the main Internet center, the subscriber easily works on the Internet at a greater distance from the main access point. That is, an increase occurred.

The main regime of the router is changing in the “control panel” of its web-intake. The exception is the Zyxel Keenetic Lite III model, which has a switch on the rear panel, which is very convenient. We click in the lower row the “system” (symbol of the gear), the “mode” tab and put a marker on its page near the inscription “Amplifier”. Press the “Apply” key. A proposal appears in the pop.up window to restart the router. We agree by clicking the “Now” button.

To establish a connection with the router, the network of which must be strengthened, shortly press the WPS button on both devices. activation of the rapid synchronization mode. The Wi-Fi indicator begins to flash. At the end of the coordination, the Internet indicator will shine constantly, which means the distribution of the Internet by the repiter accepted from the main router. After changing the operating mode, it will not be possible to go to the repiter settings at 192.168.one.one. The main router assigned him another address on the network.

Using the Wi-Fi router as a repiter: methods of settings, checking the router in a repiter mode, reset to factory parameters. Recommendations, how.

The Roter ZYXEL Keenetic LITE series is used in the organization of local wired and wireless networks for home use and a small office.

Internet center Zyxel Keenetic GIGA II model is a higher level of a higher level compared to predecessors.

A wireless network often needs to strengthen the signal or expand the coating area. This is especially true in multi.storey mansions and apartments with reinforced concrete partitions. So that such a room is evenly covered with a wireless network, as well as to provide a confident signal in the remote rooms of the apartment or a large house, use the additional Internet center of the Keenetic series. Switch it to the “amplifier” mode (sometimes it is called a repiter, a retranspace or repeater) and install it on the floor or in the room where you want to strengthen the Wi-Fi signal of the main Internet center.

Note: Important! In the “amplifier” mode, the network name (SSID), the number of the wireless channel and the security parameters (network or password key, protocol) will remain the same as in the Wi-Fi network settings on the main router. Wireless devices of the home network will be able to automatically switch between Internet centers, choosing an access point with a stronger signal.

In the “amplifier/relay” mode, connecting an additional Internet center to the main one is possible only by Wi-Fi. You can connect customers both over the Wi-Fi and Ethernet network with Ethernet network in the Wi-Fi cable network.

Note: Important! On the main Internet center, to which Keenetic will be connected in additional mode, a DHCP server should be included.

Select the optimal place for installing an additional Internet center. It is necessary to find such a place so that it accepts a confident Wi-Fi signal from the main Internet center (the most ideal option is when the “amplifier” and the main Internet center are in direct sight) and at the same time increased the coating area in those rooms where it is necessary.

To switch the operating mode in the Internet centers Keenetic Air (KN-1610) and Lite (KN-1310), translate a special mode switch to the rear panel to position “C” (amplifier). In other Keenetic models, switching the operating mode must be performed through the web configurator.On the “General Settings” page, click “Change the operating mode” and set the mode of the additional Internet center “Amplifier/Retransa”.

You will see a warning window about switching the operating mode of the Internet center. Click “Switch the mode” to confirm.

Next, you will see the state of the process of switching the mode and the information message on how to connect the Internet center to the home network in the selected mode and connect to its web configurator after changing the mode.

In the “amplifier/relay” mode, the Internet center should be connected to the Wi-Fi wireless network of the main Internet center. The connection between the amplifier and the main Internet center will be made using the WPS button. This technology is supported by most modern routers. At the same time, you do not have to know the name (SSID), the key (password) and other parameters for connecting to the main network. If the main router is not equipped with a WPS button, refer to the instruction “Example of Keenetic connection in the amplifier mode and adapter to a higher access point without a WPS button”.

So, to configure the connection between the amplifier and the main Internet center, click for a short time (do not hold, but simply press and release) once or twice (respectively, for connecting to the Wi-Fi 2,4 GHz or 5 GHz wireless network) button (WPS/ Wi-Fi) on an additional Internet center.In the same way, click the button on the main Internet center.

Note: Important! You choose only a range of information between the main Internet center and the amplifier with a single or double click of the WPS/Wi-Fi button. At the same time, both devices distribute the Internet in two ranges of 2.4 and 5 GHz. Regardless of the number of pressings, both networks intensify.

After clicking on the WPS button on both routers, Wi-Fi indicators are actively freezing. Wait until the devices agree on all parameters and automatically install the connection. This usually takes no more than a minute. Wi-Fi network parameters will be copied from the main Internet center, and you can move within the covered network coating area without changing the settings of the connected wireless devices.

What else is important to know?

Do not forget that it is extremely important to be able to properly arrange a router working in the “Repiter” mode in the room itself. The device should take a confident signal from the main router. You can even put them so that they are in direct sight. But at the same time, not very close to each other. The minimum distance between the repiter and the router should be no less than 5-7 m.

The presence between the devices of glass cabinets, reinforced concrete walls, etc. undesirable. But if you cannot install a router and amplifier differently, then you can try it and so. After all, in addition to everything else, you need to focus on ensuring that the repiter increases the coating area in those parts of the room where it is required.

Whether it will have to somehow be additionally set up the main router? In principle, no. It is only recommended that the device is connected to the global network, and the Wi-Fi access point and DHCP server are also enabled.

Zyxel router settings as a repiter?

Everything is quite simple. It is only necessary to do the following:

  • We go to the router control panel. To do this, in the address bar of the browser we prescribe “192.168.one.one”.
  • Most likely, the loaded Web-Inteatheis will need to enter the login and password. If you did not change anything, then this is “admin” and “admin”. If when connecting a router you came up with your username and password, then enter them.
  • Next, it is necessary to change the operating mode of our device to “Repiter”. How to do it? Right in the control center and settings of the router. Choosing above the “mode” tab. Then we click on the line “Amplifier-expansion of the Wi-Fi zone”. Do not forget to press and apply the button.
  • Just remember that Keenetis Lite III is not changing modes in the router control and settings center, but using a special switch on the device of the device itself.
  • Also, some integrations have no default tab “mode”. In this case, we open the “System” section, then the “Components” tab. Put ticks near 3 lines. These are amplifier modes, access points and adapter. Naturally, do not forget about the “update” button. A couple of minutes go to load the update and restart. The “mode” tab becomes available.
  • So, as soon as they activated the “amplifier” mode, a window should appear where you will be asked to restart the router. We agree and press “now”.
  • At the same time, do not be afraid if after activating the Repiter mode, you will not be able to go to the WEB-integer (settings center) of the router at the “old” address (192.168.one.one). So it should be.
  • The most important begins. We need to connect our repiter with the main router and with the network itself, which we will strengthen and retranstate. How to do it? It is necessary at the same time (of course, not up to seconds) on both devices, press the Wi-Fi button. It is also called the WPS activation button. By the way, you don’t need to keep it for a long time! Just click. this is enough.
  • After that, on both routers, Wi-F indicators should actively freeze when the devices “coordinate” all the parameters and install a new connection. As a rule, it takes no more than a minute.
  • Now on the repiter should light up the Internet indicator (WAN). It remains to try out a new wireless network strengthened by the repiter. For verification, you can go to that part of the room where there used to be a weak signal and go to the Internet through a smartphone or tablet. Or open a list of available networks, move with a gadget at a decent distance from the router and see that the signal level is excellent everywhere.

We set up ZYXEL as a repiter. Working hours. “amplifier”

We go into the settings of our router (which we will use to strengthen the Wi-Fi Network signal). We go to address 192.168.one.1 and indicate the login and password. By default. Admin and Admin. If you changed this data, then specify it. Or see the article on the entrance to the settings on the Ryxel routers.

To begin with, you need to change the operating mode of our ZYXEL to the “amplifier”. You can do this in the control panel of the router. And only if you have a Keenetis Lite III model, then you need to change the operating mode with a special switch on the back of the device. Select the “amplifier” mode, and skip the choice of mode in the control panel. If you don’t have Keenetis Lite III, then things are like this:

In the settings, we go to the System tab (below). And select the tab mode on top. Put the switch near the amplifier mode-the expansion of the Wi-Fi zone, and click on the application button.

A window will appear with a proposal to reboot the router. Click the “Now” button.

I initially did not have the opportunity to choose the operating mode of the Router Zyxel. There was simply no tab “mode”. What I’ve done:

Opened in the settings the System. Components System tab. Installed checkmarks near three components: amplifier mode, access point, and adapter mode. Then, pressed the update button. The router downloaded the necessary updates, installed, and after rebooting, everything already worked for me. The “Mode” tab appeared.

It may be necessary that the router be connected to the Internet. If you do not succeed, then see if the components on the System tab are included. update. Or, just install the latest firmware version for your model.

ZYXEL: Install the connection to expand the Wi-Fi network action area

It remains the most important thing is to establish a connection with the main router, with a network that we will strengthen.

To do this, you need at the same time on both routers (in my case on ASUS and on Zyxel Keenetic Start) click the Wi-Fi button. She is the WPS activation button. On Zyxel Keenetic Start, she looks like this:

Настройка Wi-Fi ZyXEL Keenetic. беспроводной точки доступа

On the main router (Wi-Fi of which we will strengthen). This button may look different. For example, on ASUS, which was the main thing in my case:

And this is what the button on the router TP-Link TL-MR3220 looks like:

I don’t know what your main router is, but I think that you will find such a button.

So, we click the Wi-Fi button on Zyxel Keenetic Start (which is already included in the “amplifier” mode) and on the main router. It is not necessary to press at the same time, right up to a second. At first I went, pressed this button on the main router (the Wi-Fi indicator immediately blinked there). Then he pressed the Zyxel Keenetic button (the power indicator and Wi-Fi began to actively blink actively). No need to hold the button, just click.

I waited a little, and everything was connected. How I understood that? And on Zyxel Keenetic Start, the Internet indicator (WAN) was lit up.

Opened a list of available networks, and there only one of my network was displayed there, and with a 100% signal. Although, the main router is far from me. And this means that our repiter copied information about the wireless network from the main router, and simply strengthens it. Everything is working!

I took a tablet, a trip around (from a router to a router). And the Internet worked fine. It turns out that the device is connected to a more stable network. The radius of my Wi-Fi network of certainly increased decently.

After turning off one of the routers (or both). The connection is installed automatically, and Zyxel continues to relay the network.

How to go to the settings of the “Repiter” zyxel, if 192.168.one.1 is not suitable?

After the connection between the routers is installed, go into the Zyxel settings at the usual address 192.168.one.1 (or my.Keenetic.Net). It won’t work. The page will simply be inaccessible. Even when connecting via network cable.

This is all because the main router automatically gives the IP to our repiter, and we simply does not know him. Therefore, we need to go into the settings of the main router (at the usual address). and see the IP of our router, which works as an amplifier. See the instructions for the entrance to the settings of different routers. how to go into the router settings? Detailed instructions for all models.

On the page of the settings of the main router, look for a section in which you can see all the connected devices. Something like a “list of clients”. On my old Asus it looks like this:

The list of devices will be our “Repiter”. For some reason I had an active IP address for some reason. I crossed it, and immediately got into the settings of my Zyxel Keenetic Start. If you do not know what IP you need, then you can use the poke method 🙂

There you can see all the necessary information: mode of operation, IP address, customer list, Wi-Fi network, etc. D. The menu in the “amplifier” mode will be cut off compared to the standard “Internet center” mode.

How to return the Router Zyxel Keenetic to the standard operating mode?

If you want to use your router in normal mode, for the usual Wi-Fi distribution when connecting the Internet through the cable, then we just need to change the operating mode to the main. You can do this from the settings, as I showed above. Just open the system tab (below). Then the tab mode, select the Internet center mode-the main mode and reboot the router.

Mode “amplifier/relay

Wi-Fi wireless network sometimes needs to strengthen the signal or expand the coating area. This is especially true in multi.storey mansions and apartments with reinforced concrete partitions. So that such a room is evenly covered with a wireless network, as well as to provide a confident signal in the remote rooms of the apartment or a large house, use the additional Internet center of the Keenetic series. Switch it to the “amplifier” mode (sometimes it is called a repiter, relay or repeater) and install it on the floor or in the room where you want to strengthen the Wi-Fi signal of the main router.

Note: Important! In the mode of the “amplifier” Name (SSID), the wireless channel number and safety parameters (network or password key, protocol) will remain the same as in the Wi-Fi network settings on the main router. Home network wireless devices can automatically switch between routers.

In the “amplifier/relay” mode, connecting an additional router to the main thing is possible only by Wi-Fi. You can connect customers both by Wi-Fi and by the Ethernet network cable in the “amplifier/relay” mode.

Note: Important! On the main router, to which the retranster will be connected, the DHCP server should be turned on.

It is assumed that the default device receives the IP address by DHCP from a higher main router. If the IP address has not been received, then the device is assigned a service static IP address 192.168.one.3. When a DHCP server appears on the network, the service IP address is automatically discarded and you can connect to the web configurator only by the new IP address, which will be received from the main router by DHCP.

Select the optimal place for installing a repeater. It is necessary to find such a place so that he accepts a confident Wi-Fi signal from the main router (the most ideal option is when the “amplifier” and the main router are in direct sight) and at the same time increased the coating area in those rooms where it is necessary.

To switch the mode of operation on models with a 4-position switch, set it to the “C” position (amplifier), in models with a 2-position switch to position “B” (relay). In other Keenetic models, switching the operating mode must be performed through the web configurator. On the “General Settings” page, click “Change the operating mode” and set the mode of the additional Internet center “Amplifier/Retransa”.

You will see a warning window about switching the operating mode of the Internet center. Click “Switch” to confirm.

Next, you will see the state of the process of switching the mode and the information message on how to connect the Internet center to the home network in the selected mode and connect to its web configurator after changing the mode.

In the “amplifier/relay” mode, the Internet center should be connected to the wireless network of the Wi-Fi main router. The connection between the amplifier and the main router will be performed using the WPS button. This technology is supported by most modern routers. At the same time, you do not have to know the name (SSID), the key (password) and other parameters for connecting to the main network. If the main router is not equipped with a WPS button, refer to the instruction “Example of Keenetic connection in the amplifier mode and adapter to a higher access point without a WPS button”.

To configure the connection between the additional and the main router, press the button (WPS/Wi-Fi) on the relay once or twice (respectively, for connecting to the network 2.4 GHz or 5 GHz).

Note: Important! Shortly click the Wi-Fi button and release. Do not keep it pressed.

In the same way, press the button on the main router.

TIP: Reference: in two.band models with a single or double pressing the WPS button, only a range for transmitting information between the main router and the relay is selected. At the same time, the relay will distribute the Internet in two ranges of 2.4 and 5 GHz. Both networks are intensified, regardless of the number of presses.

After clicking on the WPS button on both routers, Wi-Fi indicators are actively freezing. Wait until the devices agree on all parameters and automatically install the connection. This usually takes no more than a minute. The main parameters of the Wi-Fi network (name, password, security protocol) will be copied from the main router. You can move within the covered network coating area without changing the settings of the connected wireless devices.

After a successful installation of the connection on the retranstator, the indicator will light up (Internet). This is the setting of the Internet center in the “amplifier” mode completed.

The Internet center in the “amplifier/relay” mode will have to connect and get an IP address from the main router. This IP address can be viewed on the main router. If Keenetic acts as the main router, you can see the IP address in the web configurator on the “List of Devices” page.

In our example, Keenetic in the “amplifier” mode received from the main router IP-address 10.ten.ten.32, which will be available from the local network. Then it will be possible to go to its web-intake and, if necessary, make additional settings.

Note: Important! In the mode of the Retranstaller of the Keenetic Web Configurator menu, it will be cut off compared to the main mode (the menu items that are not used in additional operating mode will be inaccessible).

It remains only to make sure that your wireless network is now working stably and there is a sufficient signal level in those rooms where it was previously absent or was extremely low. For verification, you can use any mobile wireless device (smartphone, tablet or laptop) to search for available networks. The name of the existing home wireless network (SSID) will remain the same, and the radius of action will increase significantly.

In this mode, you can use the “Seamless Wi-Fi Roaming” (automatic switching Wi-Fi customers between routers).

We set up ZYXEL as a repiter. Working hours. “amplifier

We go into the settings of our router (which we will use to strengthen the Wi-Fi Network signal). We go to address 192.168.one.1 and indicate the login and password. By default. Admin and Admin. If you changed this data, then specify it. Or see the article on the entrance to the settings on the Ryxel routers.

To begin with, you need to change the operating mode of our ZYXEL to the “amplifier”. You can do this in the control panel of the router. And only if you have a Keenetis Lite III model, then you need to change the operating mode with a special switch on the back of the device. Select the “amplifier” mode, and skip the choice of mode in the control panel. If you don’t have Keenetis Lite III, then things are like this:

Mesh-сеть на роутерах Keenetic: покрываем интернетом трёхэтажную квартиру

In the settings, we go to the System tab (below). And select the tab mode on top. Put the switch near the amplifier mode-the expansion of the Wi-Fi zone, and click on the application button.

A window will appear with a proposal to reboot the router. Click the “Now” button.

I initially did not have the opportunity to choose the operating mode of the Router Zyxel. There was simply no tab “mode”. What I’ve done:

Opened in the settings the system system. components. Installed checkmarks near three components: amplifier mode, access point, and adapter mode. Then, pressed the update button. The router downloaded the necessary updates, installed, and after rebooting, everything already worked for me. The tab “Mode” appeared.

It may be necessary that the router be connected to the Internet. If you do not succeed, then see if the components on the System tab are included. update. Or, just install the latest firmware version for your model.

After turning on the “amplifier” mode, you will no longer be able to go into the settings of your router at the usual address 192.168.one.one. This is fine. At the end of the article I will show how to access the settings.

ZYXEL: Install the connection to expand the Wi-Fi network action area

It remains the most important thing is to establish a connection with the main router, with a network that we will strengthen.

To do this, you need at the same time on both routers (in my case on ASUS and on Zyxel Keenetic Start) click the Wi-Fi button. She is the WPS activation button. On Zyxel Keenetic Start, she looks like this:

On the main router (Wi-Fi of which we will strengthen). This button may look different. For example, on ASUS, which was the main thing in my case:

And this is what the button on the router TP-Link TL-MR3220 looks like:

I don’t know what your main router is, but I think that you will find such a button.

So, we press the Wi-Fi button on Zyxel Keenetic Start (which is already turned on in the “amplifier” mode) and on the main router. It is not necessary to press at the same time, right up to a second. At first I went, pressed this button on the main router (the Wi-Fi indicator immediately blinked there). Then he pressed the Zyxel Keenetic button (the power indicator and Wi-Fi began to actively blink actively). No need to hold the button, just click.

I waited a little, and everything was connected. How I understood that? And on Zyxel Keenetic Start, the Internet indicator (WAN) was lit up.

Opened a list of available networks, and there only one of my network was displayed there, and with a 100% signal. Although, the main router is far from me. And this means that our repiter copied information about the wireless network from the main router, and simply strengthens it. Everything is working!

I took a tablet, a trip around (from a router to a router). And the Internet worked fine. It turns out that the device is connected to a more stable network. The radius of my Wi-Fi network of certainly increased decently.

After turning off one of the routers (or both). The connection is installed automatically, and Zyxel continues to relay the network.

How to get into the ZYXEL Amplifier Control Panel, when the standard address is not suitable

After the connection between the two devices is established, get into the ZYXEL web-integer at the standard address 192.168.one.1 will not work out anymore. You will see that the web page will be no longer available. It will not be possible to get on it even when connecting via network cable. This is due to the fact that the basic router in automatic mode issues IP to our repeater, and we simply do not know it. For this reason, we first need to get into the parameters of the basic router through its standard address, and look in its settings of the IP router, which operates in the repiter mode. In the main menu of the device, you need to find a section on all connected devices. The list of connected devices will indicate a router operating as an amplifier and its IP address. If you make a transition on it, you can immediately get into the settings of the router-retiper.

Automatic setting

  • After entering the Zyxel Keenetic Lite router in the displayed window, you need to select the “Fast Settings” item;
  • After starting the Net Friend program, the provider address is indicated. If the list is missing in the list, you should click on the point “My provider is not on the list”.
  • The next step involves filling out data from the contract by manual method. MAC address is indicated on the label of the back cover of the zixel device. In some cases, it must be reported to the technical support of the provider.
  • The page opens, where the automatically configured parameters of the IP protocol are already indicated.
  • The contract with the operator contains a login and password. We indicate the data in the required fields. After that, a window appears, which indicates the current status and characteristics of the Internet connection. With any malfunction, ways to solve them will be proposed.

Client mode in standard firmware

The expansion of the coating zone of the Wi-Fi network is achieved by the manufacturer of ZYXEL by producing products, the purpose of which is the reinforcement (relay) of the accepted signal.

They are devoid of versatility, but have high technical indicators. An example is the NVA-3550 model. ZYXEL routers are devices that can work depending on their settings in different modes used to expand the Wi-Fi network action area.

We will apply the client mode (wireless bridge), which allows you to receive a signal on the air from the main router and create its own network on the same channel, with the same name and password of access. Moving in space, the subscriber selects that network whose signal is stronger, and does not feel any transition.

To configure ZYXEL Keenetic in a repiter mode, you need:

  • Change the subnet in its settings. Otherwise, the client’s connection will not occur;
  • After entering the device integer at 192.168.one.1 in the “control panel” press an icon with a home network symbol (monitor);
  • On the page opened, open the “segments” tab, and select the Home Network line in it;
  • To change the subnet, change the IP address and the initial address of the DHCP server range. Execute the command “apply”. After that, the settings are lost due to the replacement of the address.
  • Disconnect the computer from which we set up from the Zyxel router and connect again. Now, to enter the “control panel” of the custom Republic, we use the changed IP address, for example, 192.168.2.one. To connect to the main router via Wi-Fi, click on the Internet symbol (globe) in the lower row of the page. Open the WISP (Wi-Fi) tab 2.4 GHz. and install a checkplace in the cage “Turn on”.
  • After pressing the “Network Overview” key, select the one that needs to be strengthened (broadcast). Enter the access password, mark the point “Use to enter the Internet” with the marker and click the “Apply” button. To come into force, we reboot the computer. Now the Router ZYXEL REPITER works as a recurrent signal of the main access point Wireless.

Alternative firmware

The manufacturer ZYXEL on different models in the basic configuration sets the software modules responsible for certain functions. In the purchased product, the function of the repiter (amplifier) ​​is sometimes not provided for. Refresh firmware, however, is available, downloading it from the Internet. If another mode is required, for example, an adapter, it requires another firmware of the device.

With some risk of gaping guarantee on the router, alternative firmware DD WRT of a third.party developer is set. It includes all the functions of Zyxel routers, a reipiter including. Often with a universal firmware, the device works more stable than on ZYXEL.

Download DD WRT from the official website of the developer in the form of an archive, extract a file from it with an extension.bin, save it on a computer. On the starting page of the ZYXEL router, we click “Settings” (gear symbol) in the lower row and switch to the “files” tab (“micro.oprogram”). In it, we click on the “review” stencil, find the downloaded file and execute the “Replace” command. To continue, we agree with the replacement by pressing the yes button. Indicators on the front panel of the Repite will report the end of the process.

password change

Editing a protective combination has already been described above, here we will show how to change the administrator password. To do this, you need to enter the point “System” on the main page, and then. “Users”. If the guest network is not tuned on the router, only Admin will be displayed here. Default password. also admin. You need to click on it, after which the menu will appear with a change in password:

It is recommended not only to introduce it, but also to write it down in a reliable place. for example, in a phone note or on adhesive paper, which then to stick on the router itself.

By pressing the “Apply” button, the password will be changed to a new.

Zyxel Keenetic Settings in Repeater mode

Router Zyxel Keenetic Giga Generation III: New Home Center opportunities

The regime of the repeater or repiter used to expand the zone of action of the Wi-Fi network of the main router in the ZYXEL settings menu is called the “amplifier”. But the name “Retransalator” more accurately characterizes the work of the device. When the repiter is located at the place of sufficient signal force of the main Internet center, the subscriber easily works on the Internet at a greater distance from the main access point. That is, an increase occurred.

The main regime of the router is changing in the “control panel” of its web-intake. The exception is the Zyxel Keenetic Lite III model, which has a switch on the rear panel, which is very convenient. We click in the lower row the “system” (symbol of the gear), the “mode” tab and put a marker on its page near the inscription “Amplifier”. Press the “Apply” key.

A proposal appears in the pop.up window to restart the router. We agree by clicking the “Now” button.

To establish a connection with the router, the network of which must be strengthened, shortly press the WPS button on both devices. activation of the rapid synchronization mode.

The Wi-Fi indicator begins to flash. At the end of the coordination, the Internet indicator will shine constantly, which means the distribution of the Internet by the repiter accepted from the main router. After changing the operating mode, it will not be possible to go to the repiter settings at 192.168.one.one. The main router assigned him another address on the network.

On setting up Internet connection on Lite III

Open the document that you signed when connecting the Internet (cable to the apartment). Find there the mention of the protocol. PPPOE, PPTP, L2TP, dynamic or static address. The protocol must indicate data for configuration.

If nothing is noted in the contract (which is extremely rare), contact the support service. all the settings will be deduced to you and, in principle, will help you cope with debugging.

Static or dynamic address IP

Dynamic is most often used. it is easier to configure:

  • Go to the “Internet” section (marked by the globe below) and press on “Add the Inte Wee” in the second IPOE menu.
  • Put in the settings IP “Automatic”. Make sure that with ficks o, “use an exit integration”. The blue connector should also be highlighted by a bird.
  • Click on “apply”.

Indicate automatic receipt of the IP address from the provider

If you have a static address on the Internet, put in the same window to configure the “manual” value in the drop.down menu “IP settings” and enter all the data from the document (he is also a contract with the provider).

How to configure Repeater on a router

Set up Zyxel Keenetic routers to the relay function more problematic. This applies to the Keenetic Lite repiter and various ZYXEL models. However, using the tips specified in this article, you can quickly cope with the task.

Fighting the ZYXEL series, used the modular system. Therefore, it consists of individual elements. For example, in GIGA2 there is no component that is responsible for the function of the amplifier. However, this does not mean that this Zyxel Keenetic model cannot work in a repiter mode. If necessary, you can find and download the component that is responsible for connecting a WDS-motor. Thanks to this module, you can strengthen the quality of the signal or connect two networks.

Each model has a certain basic equipment. She stands on the device by default. Everything else, if necessary, can be loaded. This allows you not to overload the device with excess components.

To enable the Keenetic amplifier, you need:

Next, a list of modules should appear. Some of them are active, others are simply not installed. The list should be found “Amplifier mode”. At the level of this module, you need to put a check. After that, the message “will be installed” will appear.

If necessary, you can choose some other functions. They may be needed for work. The remaining components are installed in the same way. After all the necessary elements are selected, you need to click on the “install” under the list.

How to configure Repeater on a router

Set up Zyxel Keenetic routers to the relay function more problematic. This applies to the Keenetic Lite repiter and various ZYXEL models. However, using the tips specified in this article, you can quickly cope with the task.

Fighting the ZYXEL series, used the modular system. Therefore, it consists of individual elements. For example, in GIGA2 there is no component that is responsible for the function of the amplifier. However, this does not mean that this Zyxel Keenetic model cannot work in a repiter mode. If necessary, you can find and download the component that is responsible for connecting a WDS-motor. Thanks to this module, you can strengthen the quality of the signal or connect two networks.

Each model has a certain basic equipment. She stands on the device by default. Everything else, if necessary, can be loaded. This allows you not to overload the device with excess components.

To enable the Keenetic amplifier, you need:

Next, a list of modules should appear. Some of them are active, others are simply not installed. The list should be found “Amplifier mode”. At the level of this module, you need to put a check. After that, the message “will be installed” will appear.

If necessary, you can choose some other functions. They may be needed for work. The remaining components are installed in the same way. After all the necessary elements are selected, you need to click on the “install” under the list.

Using Keenetic routers as an amplifier

Когда используется Zyxel Keenetic 4G, режим репитера выставить довольно просто. As well as with other models of kinetics. To connect manually, you will need to enter the “system”. Next, the “mode” subsection is selected. It must be clicked on the “amplifier”. To confirm, click on the “apply” and button “OK”. After that, the device will begin to work as a repeater.

In order for the amplifier function to activate the device, you need to reboot. After that will appear a window with the instructions on how to proceed further. Those who are interested in how to connect the second router to Keenetic Air or other model, you need to consider that the IP of the Repiter will change when connecting. The address of the repeater will be the same as the main router.

Connection can be performed using the “WPS” button. It allows you to tune in in abstract. The button is located on the front panel of the device. Together with her, you need to simultaneously press the main router.

Not everyone is used with the Keenetic repeater router of the same manufacturer. In this case, you should be more attentive, since the “WPS” button on devices of other companies is often located next to the “reset”. If you click on it, you will have to re.install the device.

Possible problems of Zyxel Keenetic settings as a Wi-Fi client

1) a router configured as a client does not receive an IP address on the latest versions of the software (especially relevant when using 2x Zyxel Keenetic).

Instructions from Eugene (original comment. link, comment with screenshots. link):

“In general, who does not receive IP, you have two routers:

Go to the router 2, immediately see that he has another subnet (for example, router 1. 192.168.one.1, and router 2 do 192.168.2.1), use. Also change on the router 2 “The initial address of the pool”: 192.168.one.33 on the “initial address of the pool”: 192.168.2.33 (screenshot of settings. link)

If you enter the settings after changing the address of the router 2. Reconnect to it, or forcibly write the IP address from the router 2 range in the network settings.

When you did everything, go to the network-wi-fi-, select the right network (the one that distributes, say, a router 1, put the boxes everywhere (screenshot-link), keep, wait for 30 seconds, reconnect to the router 2 and rejoice (screenshot (screenshot (screenshot (screenshot. link).””

ABOUT AG

In this mode, it will distribute the Internet only to computers connected to the cable or Wi-Fi can connect? THX.

In this “mode” you can connect both by wire (Ethernet) and Wi-Fi.

Hello! In the repiter mode, it is possible to use a kinetics or kinetic gig 2 as a princes, or as a customer torrent, or connect an HDD. Thanks.

Good afternoon, Stanislav! When the router works in the “repiter mode”, then all its functionality is available, since for a router this is not a separate mode, but one of the possible WAN-integrates. If there are any restrictions, then I don’t know about them.

Hello! In general, I need such a scheme: my main Wi-Fi router from it Wi-Fi Repiter (Zyxel) with the ability to organize a print server file storage (HDD) with a possible download of torrents bypassing the computer., Access to HDD T.e. to films of music and pr. should be with Windows, Android and iOS DNLA TV. This scheme can provide Keenetic Giga II thank you.

I’m not sure about the print server-I didn’t try to configure. And everything else is implemented, but how high the speed will be while pumping/distributing torrent`s and viewing, for example, FullHD video from the TV-it’s hard to say, you need to test. If you configure. unsubscribe how it will work all the place, it is interesting to hear a review.

Good afternoon! I just can’t configure my Keenetic Giga II. After fulfilling all the instructions, I get a picture as you have in a screenshot, but with the inscription “WiFimaster0/Wifistation0”, condition: “Internet access”. But in reality, there is no Internet access I dropped the settings several times and repeated the procedure. it does not help. Maybe you can help me? I would be very grateful. Thanks in advance.

In the catch.up to the previous post. Maybe this information will be useful. Here’s what the system magazine writes: WiFimaster0/Accesspoint0: (RT2860) STA (F8: DB: 7F: 94: 2B: A4) HAD DISSSOCIETEDE. APR 17 09: 39: 26wmondwifimaster0/Accesspoint0: (RT2860) STA (F8: DB: 7f: 94: 2B: A4) HAD ASSOCIETED SUCCESSFully. APR 17 09: 39: 26wmondwifimaster0/Accesspoint0: (RT2860) STA (F8: DB: 7f: 94: 2B: A4) Set Key Done in WPA2/WPA2PSK. APR 17 09: 40: 49wmondwifimaster0/Accesspoint0: (RT2860) STA (64: 27: 37: B4: AD: CF) HAD ASSOCIETED SUCCESSFully. APR 17 09: 40: 49wmondwifimaster0/Accesspoint0: (RT2860) STA (64: 27: 37: B4: AD: CF) Set Key Done in WPA2/WPA2PSK. APR 17 09: 40: 49NDHCPS_WEBADMIN: Get Request with Vendor Identifier MSFT 5.0. APR 17 09: 40: 49NDHCPS_WEBADMIN: DHCPREQUEST Receved for 192.168.one.47 from 64: 27: 37: B4: Ad: CF. APR 17 09: 40: 49NDHCPS_WEBADMIN: Sending Ack of 192.168.one.47 to 64: 27: 37: B4: Ad: CF. APR 17 09: 40: 52NDHCPS_WEBADMIN: Get Request with Vendor Identifier MSFT 5.0. APR 17 09: 40: 52NDHCPS_WEBADMIN: DHCPINFORM Receved from 64: 27: 37: B4: Ad: CF. APR 17 09: 40: 52NDHCPS_WEBADMIN: Sending Inform to 64: 27: 37: B4: AD: CF. APR 17 09: 40: 53ndmdyndns :: Client: No Such Profile: _webadmin. APR 17 09: 41: 10NDMPROCESS: “Resolver” HAS Been Killed. APR 17 09: 41: 10ndmdyndns :: Client: No Such Profile: _webadmin.

Hello, Victor! Unfortunately, it is unambiguous to say what I can’t do. I need to understand. And in the settings of the router, to which you connect Keenetic, Keenetic is displayed as one of the connected devices?

I solved the problem by making it a Wi-Fi bridge And I could not figure it out with a repiter, unfortunately. But, in any case, thanks for the answer!

Victor, I have the same task as you have. Tell me how to transfer Keneetic II into a bridge mode? I’ll be very thankful)

Here are the instructions for configuring GIGA2 as a reipiter. http: // zyxel.ru/kb/3312 but still interesting mode two in one, t.e. Clients-Roter. This instruction seems to work. http: // zyxel.ru/KB/3251 writes that “the Internet is connected”, while there is even no access of the router to updates How is the “wifter-client” and “switch” intenses so “shaving”.

Internet access Wi-Fi Client WiFistation Condition: Internet access (SSID): MTS_1691568 Access point: BC: 76: 70: 03: B1: 6C MAC address: 28: 28: 5D: 63: 63: A4 Address IPV4: 192.168.one.4 Mask subnets: 255.255.255.0

Hello, I have in my settings as it is written from above, but under this it says: there is no IP address Broadband Connection ISP: no IP address IPV4: 0.0.0.0 Mask subnet: 0.0.0.0 Sent: 7.69 KB

Good afternoon! Now there is no router at hand to see, but as far as I remember, “Broadband Connection ISP” is just a WAN-integer. In your case (if you just broadcast a Wi-Fi network) difficulties should not cause.

The 3rd picture shows the condition of access and the Internet. And I have a reservation what to do?

I’m not sure, but most likely you have confusion with connections (Internet section, “connection” tab), how many active are there? Try to do actions again according to the instructions. everything should turn out.

I have good Zyxel Keenetic DSL and Zyxel Keenetic2 router, I want Zyxel Keenetic2 to distribute Wi-Fi without connecting the cable to Zyxel Keenetic DSL. T.E took Wi-Fi from the modem and scattered it. How to realize this? Respectfully

Good afternoon! Zyxel Keenetic 2 needs to be configured as a repiter, this is just written in this article. What exactly you did not succeed?

The same situation. The status says reservation. No Internet access. It is somehow not clear.

Everything worked. I figured it out. The problem was in the addresses. If you have a reservation, then prescribe the IP address and a manual subnet mask.

Good afternoon! It’s great that it turned out to figure it out. I think your comment will be useful to many.

Sorry please me for the stupidity, but as I understand this router can be used as an adapter for PC through a cable?

I did everything as indicated, but in the end writes that I can’t get an IP address, and the fat cross is red, how to fight?

Good afternoon! Where do you see red cross on the router of a router or on a network connection on PC? Please describe in more detail, preferably with a screenshot.

There is no WiFimaster0/wifistation IP state status: there is no IP address network name (SSID): Pyaterochka Access point: BC: EE: 7b: ED: CD: 7C MAC address: EE: 43: F6: DF: A4: 94 Address IPV4: 0.0.0.0 Mask subnet: 0.0.0.0 Accepted: 8.65 KB Sent: 20.29 KB