How to connect a steering wheel to a computer

How to connect a steering wheel and pedals to a computer. Step.By.Step instructions, features and reviews

Turning modern PC today into a gaming center is easy. But how to connect a steering wheel and pedals to a computer? Let’s start disassemble the procedure from the very start. Namely from the purchase of the necessary equipment.

How to make a gaming wheel for pc with mouse. #DIY

  • In order not to puzzle over the connection of a too “abstruse” device, before choosing a specific model, be sure to read independent opinions about it on the forums. If a large number of users note that they have problems with connecting the device, then this is enough to change their choice for similar ones in characteristics.
  • How to connect a steering wheel and pedals to a computer? You must have ports on your PC, to which it is possible to connect the purchase. Most often used universal USB. If the port of the port is different, then it is worth it with gaming equipment to purchase a suitable adapter. If a webcam, mouse, printer and other devices are connected to the computer via USB, then you need to buy a USB hub (brancher in other words). This will increase the number of free ports so that you are comfortable playing.
  • And one more important condition is the operating system, the characteristics of your computer should support purchased game attributes.

The choice of the necessary devices

Turning modern PC today into a gaming center is easy. But how to connect a steering wheel and pedals to a computer? Let’s start disassemble the procedure from the very start. Namely from the purchase of the necessary equipment.

  • In order not to puzzle over the connection of a too “abstruse” device, before choosing a specific model, be sure to read independent opinions about it on the forums. If a large number of users note that they have problems with connecting the device, then this is enough to change their choice for similar ones in characteristics.
  • How to connect a steering wheel and pedals to a computer? You must have ports on your PC, to which it is possible to connect the purchase. Most often used universal USB. If the port of the port is different, then it is worth it with gaming equipment to purchase a suitable adapter. If a webcam, mouse, printer and other devices are connected to the computer via USB, then you need to buy a USB hub (brancher in other words). This will increase the number of free ports so that you are comfortable playing.
  • And one more important condition is the operating system, the characteristics of your computer should support purchased game attributes.

And yet we will not offend the steering wheel, this is not a flash drive

But frankly, the steering wheel and pedals are still not a flash drive, it may not come to such an elementary region. Over, most likely, the phrase will be different, something like “the device is not ready” or “the device is not recognized”.

It’s okay, this is a normal course of things. So, the system did not recognize your racer, has no drivers for them and offers to install them on its own.

To do this, we insert a drive with a steering wheel and pedal software into the CD string, this disk is included in the kit of products. The equipment installer from the disk is launched automatically. Install all drivers and programs, perhaps we reboot the computer.

CD with steering and pedals software

Further, you are not going to use pedals and steering wheel for racing according to the system files, it is not in the “my computer” to use these equipment a la Senna.

Therefore, to test the installation, you will need to start some game and try to manage already with the steering wheel, not forgetting to slow down and accelerate the pedals.

Self.Manufacture of the steering wheel

So, make a steering wheel and pedals to a computer. Scheme and description will be presented later. Let’s make a step.By.Step analyze the algorithm:

  • The steering wheel can be cut out of wood, glue from several plywood plates. First of all, you need to use the line and circul to execute its detailed drawing on paper.
  • Further, a hub is made of hard wood, which is attached to the rear of the steering wheel using screws or furniture glue.
  • A hole is drank through the steering shaft. A bolt with a cut head is inserted there. Its ends are grinded by a file. Holes are drilled in the resulting sites. Springs are installed in these places.
  • To fix the nuts, the steering shaft also grows on both sides.
  • The bolt is twisted into a drilled hole on the axis. On both sides it is pulled away by nuts. The second side of the spring is attached to the L-shaped bracket.
  • Another important stage is to perform the mounting system to the table. Bend the P-shaped bracket from the metal plate. It makes 4 holes for screws.
  • The next stage is the manufacture of a clamping paw. A hole for 5 mm bolt is drilled in it in it.
  • With self.Tapping screws, the foot is connected to the bracket so that it can move freely.
  • From the base of the module to the foot should be a distance equal to the thickness of the table.
  • Then the master drilles the hole through the base of the steering module. A T-shaped carvings sleeve is inserted here.
  • P-kronshtein screws up to the wooden base of the module.
  • A bolt with a rotary handle is passed into the hole of the foot, after which it is screwed into a T-linen.

How To Connect Logitech G920 Steering Wheel To Your PC! | Tutorial

Then you need to take care of the electronic “filling”.

Something like this we make pedals and steering wheel to a computer. Another version of the homemade in the video below.

We make a steering wheel and pedals to a computer

To make a steering wheel and pedals, just buy several details, read instructions and tips and work a little with your hands. How does it all work. Most personal computers used for games have a sound card. There is a gamort on this map in which you can connect joysticks, gamepads, steers, etc. All these devices use the capabilities of the gaming port the same. The difference is only in the design of the device, and a person chooses what is the most suitable and convenient for the game in which he plays. The personal computer gamest supports 4 variables (potentiometer) and 4 instant buttons-switches (which are turned on while pressed). It turns out that you can connect 2 joysticks in one port: 2 resistance (one. Left/right, the other. Up/down) and 2 buttons for each.

If you look at the sound card, you can easily see the gamort, as in this figure. Blue indicates which needles in the port correspond to the joystick function: for example, J1 x means “joystick 1 axis x” or BTN 1. “button 1”. The numbers of needles are shown in black, it is necessary to count from right to left, from top to bottom. When using a gimport on the sound board, you need to avoid connections to needles 12 and 15. The sound card uses these outputs for MIDI to transfer and receive, respectively. In standard joystick, the X.Axis potentiometer is responsible for the movement of the handle to the left/right, and the resistance of the axis Y. Forward/backward. With regard to the steering wheel and pedals, the axis X becomes control, and the axis Y, respectively, with a throttle and brake. The y axis must be divided and connected so that 2 separate resistances (for gas and brake pedals) act as one resistance, as in standard joystick. As soon as the idea of ​​a gapport is clear, you can begin to design any mechanics around the main two resistances and four switches: steering wheels, a motorcycle handle, control of the aircraft traction. How much the imagination allows.

The steering module. This section will tell how to make the main steering wheel module: a desktop casing containing almost all mechanical and electrical components of the steering wheel. The electrical circuit will be explained in the “Problem” section, mechanical parts of the wheel will also be covered here.

In drawings: 1. Steering wheel; 2. Wheel hub; 3. Shaft (bolt 12mm x 180mm); 4. Screw (holds the bearing on the shaft); 5. 12mm bearing in the support casing; 6. Centering mechanism; 7-bolt limiter; 8. Gears; 9. 100k linear potentiometer; 10. Plywood base; 11. Rotation limiter; 12. Bracket; 13. Rubber cord; 14. Corner bracket; 15. Gear shift mechanism.

The drawings at the top shows the general plans of the module (without the transfers mechanism) on the side and in the form of from above. To give the strength of the entire design of the module, a box with beveled angles of 12mm plywood is used, to which 25mm protrusion for attaching to the table is attached to the front. The steering shaft is made of an ordinary fastener bolt 180mm long and 12mm with a diameter. The bolt has two 5mm holes-one for the bolt limiter (7) that limits the rotation of the wheel, and one for the steel finger of the centering mechanism described below. The bearings used have 12mm inner diameter and are screwed to the shaft with two screws (4). The centering mechanism is a mechanism that returns the steering wheel to the central position. He should work accurately, efficiently, be simple and compact. There are several options, one of them will be described here.

Mechanism (Fig. Left) consists of two aluminum plates (2), 2mm thick, through which the steering shaft passes (5). These plates are separated by four 13mm inserts (3). A 5mm hole was drilled in the steering shaft, into which the steel rod is inserted (4). 22mm bolts (1) pass through plates, liners and holes drilled at the ends of the rod, fixing all this together. The rubber cord is wound between the inserts on one side, then along the top of the steering shaft, and, finally, between the inserts from the other side. Cord tension can be changed to set the wheel resistance. To avoid damage to the potentiometer, it is necessary to make a rotation limiter of the wheel. Almost all industrial rudders have a range of 270 degrees. However, the rotation mechanism by 350 degrees will be described here, which will not be a problem to reduce. Steel G-shaped bracket, 300mm (14) with bolts to the base of the module. This bracket serves for several targets:. Is a place for fastening the rubber cord of the centering mechanism (two M6 bolts 20 mm at each end);. Provides a reliable point of stopping the rotation of the wheel;. Enhances the entire structure at the time of tension of the cord.

Bolt limiter (7) M5 25mm with a length of 25mm is screwed into the vertical hole in the steering shaft. Directly under the shaft into the bracket, a 20mm m6 bolt is screwed (11). To reduce sound when hit on bolts, you can wear rubber tubes. If you need a smaller angle of rotation, then in the bracket you need to screw two bolts at the required distance. The potentiometer is attached to the base through a simple corner and connected to the shaft. The maximum rotation angle of most potentiometers is 270 degrees, and if the steering wheel is designed to rotate 350 degrees, then a gearbox is required. A pair of gears from a broken printer will do perfectly. You just need to choose the right number of teeth on the gears, for example 26 and 35. In this case, the transfer number will be 0.75: 1 or a rotation of 350 degrees of the steering wheel will give 262 degrees on a potentiometer. If the steering wheel spins in the range of 270 degrees, then the shaft is connected to the potentiometer directly.

Pedals. The basis of the module is made similarly to a module of a steering wheel of 12mm plywood with a cross member of solid wood (3) for attaching a return spring. A gentle base shape serves as a stand for the legs. The pedal stand (8) is made of 12mm steel tube, by the upper end of which the pedal is attached with bolts. A 5mm rod passes through the lower end of the rack, which holds the pedal in mounting brackets (6), screwed to the base and made from a steel corner. Cross (3) passes through the entire width of the pedal module and reliably (must withstand the complete stretching of the springs) is glued and screwed to the base (2). The return spring (5) is attached to the steel screw with the ear (4), which passes through the cross.Member directly under the pedal. This mounting design allows you to easily adjust the spring tension. The other end of the spring clings to the pedal rack (8). The pedal potentiometer is installed on a simple L-kronstein (14) in the rear of the module. Carry (11) is attached to the drive (12) on the bushings (9, 13), allowing the resistance to rotate in the range of 90 degrees.

How to quickly connect the steering wheel with pedals to a computer

Before connecting the steering wheel to the computer, it is necessary to assemble it (it’s not about the computer), because it comes out of the box in parts. Separately the steering wheel with electric drive, separately the pedal node and possibly separately the checkpoint itself, although most often the checkpoint and the steering wheel combine in a single case. So, for example, the pedal node is connected to the steering mechanism by means of a special connector, and all together is connected to the computer system unit through a conventional USB. Accordingly, on the panel of the system unit, it is necessary to have at least one free USB port.

Well, then the matter of technology, as they say. Just stick the power supply unit into the outlet and a notification should appear on the screen that Windows has found new equipment. If something like “equipment is not recognized” is displayed-then you will have to install the drivers, but more on that below. The secret of “fast” connection to PC is that you do not have to use the software disk that comes with the steering wheel. What are the disadvantages of this method? In some games, this “device” may work incorrectly or not work at all.

A typical example is the inconsistency of the initial positions of the steering wheel, when he is in the center in the game itself in the center, and in reality it is turned to some corner. Or, another problem when in some simulator about the rally (where the steering wheel in the cockpit, in principle, turns only by half a turn in each direction), your “physical” steering wheel makes several revolutions in each direction. That is, on the screen, he was already “rested” at the limiter, and you are still twisting it.

So that there are no such problems, it is necessary to put an additional. For example, Logitech’s rudders are freely available for the Logitech Profiler application, which allows you to configure the maximum number of steering speeds, “feedback” (turning force) and many other settings, including manual setting of certain buttons for specific actions in games. And the same application allows games to correctly determine the device and use all its capabilities.

Why do you need a XPadder program?

Of the functionality of the Xpadder, we note:

  • Convenient control program due to visualization of the process of setting up the gamepad (the screen displays an interactive image of the selected game controller with signed animated buttons).
  • Support for Force Feedback. Tactile feedback of a game controller (for example, the vibration of the joystick).
  • Support for wireless gaming Bluetooth controllers.
  • The ability to emulate the keyboard/mice from 16 gaming devices at the same time (t.E. Support for multiplayer games or managing one game for several players).
  • The possibility of creating, preserving and subsequent loading of an unlimited number of profiles with settings (saved profiles can be shared with friends or, conversely, use other people’s profiles on your computer).
  • The ability to create global hot buttons to control by means of gaming devices by any programs operating in the background.

Connection of the device

In the box, along with the steering wheel and pedals, all the wires necessary to provide contact with the computer should lie. As a rule, there are 2 cables in the box. One is needed to connect the steering wheel and the other for pedals. You need to connect them, and then insert the other end into the free USB connector.

Sometimes the kit includes a gearbox that needs to be attached to the steering wheel using a separate wire. As a rule, such a task does not cause difficulties when using the instructions.

Attention! In the presence of additional nutrition, it must also be used before starting the gameplay.

Setting controller or steering wheel manually

Even the installation does not always solve the problem: the system has not seen the gamepad, does not see. Here, the user is invited to perform a number of simple operations:

connect, steering, wheel, computer

It remains to be calibrated and tuning the controller, after which it will be possible to run the simulator and play.