How to connect the remote control to a Samsung TV

Typical problems encountered by users

It is not uncommon for users to encounter problems starting a Smart TV. Here are typical problems.

See the table for connection problems and possible solutions:

  • low-powered processor. Then it is recommended to change the equipment to a more powerful one;
  • low internet speed. You should contact your ISP and switch to a higher speed
  • The router may be located too far away. It is necessary to move it closer to the TV;
  • low internet speed. You need to increase it at your provider
  • Update the software;
  • check the TV settings;
  • Check the working order of the socket and make sure the contacts aren’t loose

Attention! Optimal is considered to be an internet speed of at least 10 MB/s.

How Smart Touch Control differs from the pushbutton remote control

Users often encounter problems with launching Smart TV. Here are some typical problems.

See the table for connection problems and possible solutions:

  • low-powered processor. Then it is recommended to change the equipment to a more powerful one;
  • low internet speed. You should contact your provider and set a higher speed
  • the router may be located too far away. You need to move it closer to the TV;
  • low internet speed. You need to increase it at your provider
  • Update the software;
  • check the TV settings;
  • check if the socket is working properly and make sure the contacts aren’t loose

Attention! Internet speed of at least 10 MB/s is considered optimal.

Connecting the proprietary Smart Touch Control

Smart Touch Control is a remote control, equipped with a touch pad and a microphone. The branded accessory allows the user to simplify the navigation in the “smart” menu and the process of finding information on the Internet.

Synchronizing Smart Touch Control with the TV is as follows:

In some cases for the successful synchronization of the devices you may need to reboot the TV. It is important to note that the process of connecting the Smart Touch Control remote control can be different from the presented algorithm. the exact sequence of actions depends on the series of TV set.

Below are the main differences between the touch remote control and a classic one:

Externally, ST Control differs from the usual Samsung remote with touch keys to navigate menus and a physical button to launch the voice search. Find more information about the branded accessory on the manufacturer’s official website.

Beeline

Early models of remote control devices from this company had many flaws, because they could only be connected if the user had a special set-top box. Also the remote control had no “SETUP” button. However, Beeline has corrected and released an improved version of the remote control equipment. The remote control is smaller in size, but has acquired a greater number of functional buttons.

See also  How to sign in to Samsung if you forget your password

To pair a Beeline remote control with a signal receiver, you will need to follow the following step-by-step instructions:

  • Turning on the TV.
  • Press “C” and “SETUP” buttons.
  • Waiting for the completion of initialization.
  • When the LED blinks twice, you can release the buttons.
  • You can check the operability of the device by pressing the “VOL” button.

Each of the remote controls has its own algorithm of adjustment, which should be described in detail in the instruction manual, coming with.

What to do if the connection fails

connect, remote, control, samsung

If after connecting the remote control does not work, the following steps will help to solve the problem:

  • Recharging the batteries. You can see the low battery symbol on the monitor.
  • Reinstall the batteries. It is possible that the first time they were misplaced. If you have done everything correctly, the connection will be established.
  • Reboot your TV. To do this, it is recommended to remove the plug from the socket and put it back in a minute.
  • Perform the setup again. It is possible that an error was made the first time.

Samsung Smart Control is a touch-sensitive remote control that makes it easy to control your TV. You can configure the device yourself. For this purpose it is recommended to carefully study the instruction above.

How Smart TV works in Samsung, LG, Sony TV, video.

Remote control connection instructions

F-series remote control

  • Insert either AA or AAA batteries into the remote control;
  • Turn on the remote control;
  • Press the button on the back panel;
  • Hold your finger on the button until the Bluetooth icon lights up on the screen.

J-series devices

  • Insert two AA batteries;
  • Turn on the TV;
  • Press 2 buttons at once. Return and Guide;
  • Press and hold your finger on the buttons until the Bluetooth icon lights up on the screen.

Set up H series remote control

  • Insert two AA batteries;
  • Turn on the TV;
  • Press 2 buttons at once. Return and Extra;
  • Hold your finger on the buttons until the Bluetooth icon lights up on the screen

K-Series

  • Insert two AA batteries;
  • Switch on TV;
  • Press the Back and Play buttons simultaneously;
  • Hold your finger on the buttons until “Connect to Remote Control” lights up on the screen.

The rarer M, Q and LS series

  • Insert 2 AA thumb batteries;
  • Turn on your TV;
  • Press two buttons at once. Back and Play;
  • Hold your finger on the buttons until “Device Search” lights up on the screen, then “Connect to Remote Control” should appear.

When you connect your remote control for the first time, it is recommended to keep a distance of 1 meter from the remote control to the TV.

See also  How you can connect your phone to the TV

Setting up the universal remote control for Samsung TV

There are two ways in which you can connect the universal remote control to a Samsung TV. manual or automatic. It is necessary to pay attention to the fact that any universal remote control (remote control) works on the same principle as a brand-name remote control.

Why does Megogo not work on your TV: causes, what to do?

Auto

Turn on “Auto Search” in the settings, and type “9999”. Do not release the last nine until the receiver is turned off. Once enabled, the algorithm will be as follows:

  • point the remote control to the TV;
  • Press and hold “Power” button for 3-5 seconds;
  • Press “SET” and “Power” again;
  • enter the code;
  • save;
  • Go out.Tap twice on “SET”.

Samsung one remote control pairing. RESET

Manual

First, take the remote control tool, and insert the batteries into it. Run it by pressing “Power” (usually the key is highlighted red and above the others). Then press “Return” and “Play/Stop” simultaneously, hold it for up to 4 seconds and release it. point the IR port to the TV. After this action, a loading window will start on the screen is “Search for Devices”. After 1 to 2 minutes the TV will find the stand-alone remote control and request to connect to it. Enter the code and complete the pairing.

Without a code

Authentication without a special code is possible if your TV-device has the following settings. Then use one of the above options for connection, only omitting the step with entering the combination.

  • turn on TV;
  • Press and hold the TV and OK keys simultaneously for 2-4 seconds;
  • Press CH or CH- (moving through the channel list) until the TV turns off;
  • After each pressing wait 2-3 seconds and then click again;

If the TV does not respond to the remote control, make sure the batteries are serviceable. If the replacement did not help, please contact the “Lenbyt” repair shop. It could be a failure of the TV receiver itself, not the remote control. Skilled craftsmen will quickly identify the source of the problem and fix it at home.

Setting universal remote controls

Remote control must be powered by installing batteries or rechargeable batteries. Batteries are not included. they must be purchased separately. Batteries are recommended; although more expensive, they provide for recharging.

Then turn on the TV set you are going to use the remote control with. Press “TV” button for 3 seconds to set the mode (TV, DVD, Audio or PVR) until the LED on the front of the receiver lights up.

Further steps are different. If you know the code. do the manual tuning, if not. do the automatic tuning.

Automatic

Press “9999” on the remote control and do not take your finger off the button until the TV reboots. If everything is done correctly, the automatic channel search will start, which lasts up to 15 minutes. The method is working and up to date, if the code is not found in the directories.

See also  How to connect the remote from the set-top box to the TV

That is how the channels are found.

For new Samsung, Panasonic, LG, Philips TV usually take universal remote control from Supra. How to set it up:

  • Turn on the TV and point the remote control in its direction.
  • Press “Power” button on the remote control for 5-6 seconds, until LED lights up.
  • A volume icon should appear on the screen. If it can be increased or decreased. the tuning is successful.

Button “Set” on the remote control. Manual for Huayu R/C:

  • Turn on the TV receiver.
  • Press “Set” and then “Power” on the remote control and simultaneously release them.
  • Press “Power” again.
  • The display shows a volume icon.
  • To exit the settings, press “Set” twice.
  • Turn on the TV.
  • Press “TV” button until the LED lights up.
  • Press “Mute” to activate search.
  • Check if the TV set responds to the pressings on the remote control.

Manual

In this case, we will need the pairing code. After pressing it perform specific actions, depending on the remote control.

  • Supra. Point the remote control at the receiver, press “Power” button, the window will appear on the screen and enter the code. The LED will confirm by blinking that the correct combination is selected. Release “Power”;
  • Huayu. Press “Power” and “Set” until the LED flashes. Enter the 4-digit code. When the LED is off, press “Set”;
  • Beeline. Press “C” and “Setup” buttons. The LED will blink twice. the initialization is completed. Release the buttons and check the “bundle” by adjusting the volume.

You should enter the TV code within 1 minute. After that the device switches to normal mode and the procedure has to be repeated again.

Without code

If there is no digital combination, it can be found. How to do this:

  • Turn on your TV and point the remote control to it.
  • Press “TV” and “OK” for 2-3 seconds. During this time all the buttons on the remote control will glow. Wait until all except the ones that light up the numbers go out.
  • Without haste press the button that switches the channels “CH” until the TV turns off, which will indicate a successfully matched code.
  • To save the settings press “TV”.

There are no unique settings of a universal remote control for TV, each brand has its own algorithm of actions. But there are some similarities that can be drawn from the described recommendations. In any case, the UPDU is a handy device used to control all electrical equipment in the house.