How to connect Wi-Fi to Epson printer. Educational video: as Epson settings…

This material will help to connect and configure Wi-Fi on the Epson printer of popular models L366, L805, L355, L3060, L386, PIXMA MG 3640 and many others including. Here are considered all the ways to “knit” a device with a wireless network via WPS, entering a PIN code and the SES function. Separately given recommendations for setting up the print by “Wi-Fi” from a computer, laptop, phone or tablet. It also shows how to correctly install drivers (software) for your Epson.

Almost any model of the Epson Printer “L” is equipped with a special wireless radio module. It is that allows you to connect the device with a local network in one bunch. And this already makes it possible to print documents or photos from other devices in the same network. It can be computers, laptops, smartphones and even a tablet.

If the printer is only bought and this will be its first inclusion, then it is worth preparing to correctly. First of all, you need to fill the banks of the system of continuous supply of ink with paints of the desired shade. SNPCh is located on the left, and dyes often come with the equipment with technology. But you can buy them separately in any computer store.

After each refueling, it is recommended to carry out software cleaning of the snot and the underflowing head. To automatically start the procedure, click for a few seconds button a triangle in a red circle. She is the most extreme on the right on the panel.

Wi-Fi connection methods

Wi-Fi Protected Setup (WPS)

The technology allows you to “tie” two devices using Wi-Fi in one network. To do this, apply according to the following instructions:

  • On the front control panel, which is located directly on the printer housing, find and click the “Wi-Fi” inscription button.
  • Keep it pressed at least three seconds.
  • When the bulbs on the panel start blinking in turn, click the WPS button on the router.
  • The work of indicators should change to simultaneously flashing together.
  • The connection between the devices is established successfully.

Entering PIN COD

Unfortunately, not all routers have a WPS button, and therefore you will have to use the method of entering a special PIN code. It is located below on the printer case on the sticker with information about the serial number and the MAC address. Consists of eight digits, which are divided into pairs of 4 pieces by hyphen. The code must be recorded or remember.

Now you need to go into the settings of the router. In most cases, this is performed through a web-integer. Open the browser and enter into the line “192.168.one.1 “or” 192.168.one.0 “. The exact IP is indicated on the router label. There is also the data for the entrance: Login and password. By default, it can be “admin” and “1111” if the setting of network equipment was not carried out earlier. And you can also try to log in with the entry data in Wi-Fi.

In the admin part after the entrance, find the menu section with the name WPS (can also be indicated as “QSS” or the full name of Wi-Fi Protected Setup). Now press the button or link that adds a new device. Enter the printer code Pin. Save changes if it is required.

Epson EcoTank WiFi Direct Setup For ET-2720, ET-2750 & ET-2760

Secureeasysetup function (SES)

  • Turn on your router and wait until it starts to work.
  • Disconnect the USB cable or network patch cord from the printer. Pay attention to the indicators of the network state on the printer case. The orange or both bulbs (there is still green) should be burned out. Only after that you can continue the connection.
  • Find, press and hold the SES button on the router. Its location may also be indicated in the instructions for equipment. Let go only when it starts to blink.
  • Now click the Wi-Fi button on the printer case. Both network indicators will begin to flash different colors in turn. As a rule, it is green and orange.
  • After a successful connection, the light bulbs will begin to work at the same time. Wait until the green indicator lights up. This may take up to five minutes.
  • If only green flashes, then this means that the connection is not completed. Click once again on the Wi-Fi button and conduct the procedure again.

Established a connection between devices?

  • No, nothing happens. 90%, 9 votes 90% 9 votes. 90% of all votes
  • Oh sure! 10%, 1 voice 1 vote 10% 1 vote. 10% of all votes

Total votes: 10 23.01.2020 × you or from your IP have already voted.

Epson L3050: network settings

Open the specified B-s Ait and introduce your mouth to your mouth.

PROTH DIALS I T LI TO RULITAL AND LOVE POWNLOAD IN THE SECRIPTION “LOVING AND SECRIPTION”. Twice

Click the uploaded file for the proof of the programs of the must. After eating tjing on the screen on the screen.

❏ Nast Rory using a disk with program about a sedate (only for the fashion of lei, which are after

with a disk ok with software about exposure, and user, whose computers are equipped with a disk

Put in a di s to with software about the sediment to the computer and after drinking tfsi on the screen.

Complete the instrument on the screen, until it is bored with the ice screen n, in the nib Rita Me Tod

Select the type of connection and click those.

Trace in the hand on the screen on the screen. The necessary program is maximum.

Connection Inte lilet T

You can use the printer with the intelligence of the UAL mustache when connecting the printer to

W I-Fi with that (SSID), as the network to which the intelligence is connected by the. For use

Print of ERA from the intellectual device perform those configuration with the paved to the same.

Go to the web-sit with the STR, which you want to connect to the NTER.

If you want those simultaneously connected to the computers and intellectual lines,

The river is the eTs from the chalfed.

We are three W I-F I from the control panel

We have trials from the printer control panel. After the DC of the Printer Personal to Ce

Connect PR to Clean. with whom you want to use it (to the computer. Smartphone y ,

“On with t r ohk a w i.FI with the Obosch KN OPKI »n a s t r. twenty

“Nast Rory W I-Fi with helping us with a pin-code (WPS)” on page. 21

You are the same automatically dangle the network W I-F I, by pressing the PC but to the point of. If executed

the following conditions, you can use this method b.

❏ T points to s to UPA Combining from Tim with WPS (we are on the roof wi.Fi).

❏ Tskaling W I-Fi was created with the OSH on Zatiya KN OPK and for the bottom of the dos t.

If you do not wait to find to the NOP K or you are in the nast Roy Ku using the software, I will turn to the documentation

Holding the Ayy button at [wp s] at the dos t point for PA until it starts to mile

If in the ss are those where the [WPS] button is located, the liberty is studied, if there are no buttons at the dos tp point,

about the document to the dos tp pup.

Click and hold the button on the reprition panel of the printer om until green

indicator, located on the left, and an orange indicator, a native certificate a, I will not start t

FLANT FLASED (about 3 seconds for ND).

The connection is set up. When the connection is installed, the green indocation of the ator, the adjustable

on the left, and the orange indicator located on the right, is in the way. Orange

The indicator, a navigable certificate a, will automatically turn off CT 5 mine t.

If the green indie the hardware is turned off on the left, and the orange indie to the atore on the right flashes, then

the mode of errors in the connection. Out of throwing the error of the rinter with power, the ken on the buttons K and

Comte the role of the Noah panel and reboot the access point, put it closer to the rint of the nonsense and try again.

In case of failure, in the print, the component is the connection and the resolution of the problem is.

“About the return of the VOGO with the dwells of the Inen”. 2 2

“It is impossible to perform a nast of the roying of CE”. 103

Settings A W I-FI with the prayer of the PIN-COS settings (WPS)

You can be wrapped in a dos tp point using a Pin code, printing on a fox tke with that.

This method is used if the point is applied to the function WPS.

Epson EcoTank ET-3850 WiFi Setup

For the mustache of the PIN-code at the dos t u pa.

Click and take off alive in the pressed pc pc

on the reprition panel of at least 1 0 seconds for ND.

The sheet of the network is displayed from I to print.

will keep less than 10 with Eku ND, the print will be displayed on the network

connection. About the attention that in this from this from the TS of the information about PIN.to de.

Holding the pressed PC at. click and der live but PC for until green

indicator, located on the left, and an orange indicator, a native certificate a, I will not start t

one temporarily instant (about 3 seconds).

Using an output and enter Pin-Ko D (into a second number), a decree in a number of oncs [WPS-PIN

COD E] In the same way, the CAS Set and, in the ChKU to the STEA (prior, is a fate of it

In the ultrasound of the connection, the green indicator, the native of the jale, and the orange indicator,

Located to the right, Bud. Orange indicator, located on the right,

the car will be mattically turned off h here z 5 mine t.

❏ For the pain under the Robny Information and the introduction of the PIN code, ITA to documentation and to the access point.

❏ If the green indie to the atore on the left in the yk is hatch, and the orange in the dikator flashes on the right, then it goes

in the reign of the connection errors. After throwing an error with a nra, using the extension of the button

Control panel perepov Obz Currently DOS TUP A, place it closer to the NTER and try again

once. In case of failure to print a report on the one and in the saber of the decisions.

“Lee STK and with a hundred INS Network” n and p. 2 7

“About the return of the VOGO with the dwells of the Inen”. 2 2

“It is impossible to perform a nast of the roying of CE”. 103

Checking the Slavia Set Evo from the Odentification

Overek with an oh oh, and with a dowry

SSID connection connection

How to connect Wi-Fi on an Epson L355, Epson L366 printer and other similar models:

  • You will have a list of Internet access networks, which Epson L355 was able to detect using the Wi-Fi module in the nearest radius. If you do not remember what your network is called and cannot choose the right one, then look at its name on your other devices connected to the Internet. They all have a setup of connection to wireless networks, so you will not be difficult to find out the necessary data.
  • Then you will need to enter a password. If you do not remember it, you can turn to the item above, there is also a chance to find out the necessary data.

If all of the above steps are successfully completed, the result will not be long in coming-the light signal over the inscription “Wi-Fi”, located on the printer in front, will immediately light up green. This means that the printing device is successfully connected to the network.

SSID connection connection without password

You say: all this, of course, is great, but how is the second way? There is a division into two ways: through a small screen of the printer or without it. The difference between them is not serious, so then we will describe both methods at the same time.

Without a pin code

So, if your printer has a LCD display that makes it possible to control the device, then we pass the first three menu items as in the instructions above, and then select “Connection using the WPS button”.

If not, press the Wi-Fi button on the device panel.

Further, the printing device will scan wireless networks around it and try to connect to any of them. Information about the next set of settings will appear on the LCD screen, and the light signal will start blinking.

Then you will need to contact the router. the omnipotent distributor of the wireless Internet of your home. As a rule, on the right in the rear panel of this device there is a button marked WPS or, which is more rare, QSS. Click it and Wi-Fi router will think that the printer requiring access is a friendly device, and not your neighbors from below, eager for free Internet at someone else’s expense.

If everything went successfully, then the light indicator will stop flashing and light up in green. This is a direct signal to the fact that you can start to print without experiences. If an orange color is burning, then this means that there is no connection, and the right step here will check the performance of the router itself.

With a pin code

If the router does not have a rapid WPS connection button, do the following (using the example of a TP-LINK router):

  • On the printer we are looking for an 8-digit pin code, which is indicated on the sticker.
  • We go to the router integration. To do this, in the search engine we enter the address indicated on the router. There is also a login and password for entering the settings (if you have not changed them to your own).
  • We go to the WPS section, press the button for adding a new device and enter the PIN code indicated on the printer.

If you have questions or found a mistake in the text, our instruction seemed incomplete or incomprehensible to you, let us know! Leave Комментарии и мнения владельцев and we will try to answer your questions! Your Комментарии и мнения владельцев will help us make better material in the future!

The first connection of Epson L355

Before the first turning on, season the system of continuous ink supply located on the right side. For this, four bottles with ink of different colors are delivered in the kit. Detailed step.by.step instructions can be found in the insert, which is also included in the set of delivery.

After refueling the printer, insert the power cord in the connector on the rear panel. Connect the cable to the outlet and click the power button located on the left on the control unit. The EPSON device will diagnose and report its completion by flashing the LED. This process usually takes no more than 1-2 minutes.

Important! After the first refueling, it is necessary to start cleaning the printing heads of the printer. To perform this action, press and hold the extreme right button for 4-5 seconds.

Installation of Wi-Fi compounds

A wireless connection to a local network is installed using Wi-Fi Protected Setup (WPS) technology. It allows you to add a new network device in one of two ways:

In the first case, it is enough to press and hold the Wi-Fi button on the front side of the All-In-One Printer Epson for three seconds. When the first two LEDs begin to turn on alternately, click “WPS” on your router. With a successful installation of the connection, the operating mode of indicators will change. They will turn on and turn off at the same time.

If there is no “WPS” button on the router, use the second network connection method. Check PIN on the bottom panel of the Epson printer. The desired code consists of eight digits, divided by a hyphen into two blocks of four characters. You can find it in the last line of information on the sticker, under the serial number and MAC address All-In-One Printer Epson.

Open the router of the router in any browser. The standard entry data can be found on the sticker at the bottom of the device. To go to the administrative panel, enter the specified IP in the address bar. In the authorization window, indicate the login and password from the router. Go to the “WPS” section and click on the link to add a new device. Enter the PIN code specified at the previous stage.

note! In some models of routers, this menu may be called “QSS”. It is also possible to use the full name: Wi-Fi Protected Setup.

The first connection of Epson L355

Before the first turning on, season the system of continuous ink supply located on the right side. For this, four bottles with ink of different colors are delivered in the kit. Detailed step.by.step instructions can be found in the insert, which is also included in the set of delivery.

After refueling the printer, insert the power cord in the connector on the rear panel. Connect the cable to the outlet and click the power button located on the left on the control unit. The EPSON device will diagnose and report its completion by flashing the LED. This process usually takes no more than 1-2 minutes.

Important! After the first refueling, it is necessary to start cleaning the printing heads of the printer. To perform this action, press and hold the extreme right button for 4-5 seconds.

Installation of Wi-Fi compounds

A wireless connection to a local network is installed using Wi-Fi Protected Setup (WPS) technology. It allows you to add a new network device in one of two ways:

In the first case, it is enough to press and hold the Wi-Fi button on the front side of the All-In-One Printer Epson for three seconds. When the first two LEDs begin to turn on alternately, click “WPS” on your router. With a successful installation of the connection, the operating mode of indicators will change. They will turn on and turn off at the same time.

If there is no “WPS” button on the router, use the second network connection method. Check PIN on the bottom panel of the Epson printer. The desired code consists of eight digits, divided by a hyphen into two blocks of four characters. You can find it in the last line of information on the sticker, under the serial number and MAC address All-In-One Printer Epson.

Open the router of the router in any browser. Standard entry data can be found on the sticker at the bottom of the device. To go to the administrative panel, enter the specified IP in the address bar. In the authorization window, indicate the login and password from the router. Go to the “WPS” section and click on the link to add a new device. Enter the PIN code specified at the previous stage.

note! In some models of routers, this menu may be called “QSS”. It is also possible to use the full name: Wi-Fi Protected Setup.

How to connect All-in-One Printer or Epson Printer by Wi-Fi

Connecting Epson Wi-Fi Printers of common models (L3050, L805, L366, L486, L4160, L6160 and others) is very simple.

Connect the computer or laptop to the same wireless network to which the printer will be connected, then the following steps:

  • Go to Epson website.SN, enter the model of your printer at the search window and click Enter.
  • Click on the “Settings” item, and then “download”, the proprietary program Epson Install Navi is downloaded, which allows you to easily make subsequent configuration. Run it.
  • At the first stage, the program downloads and set the necessary drivers, and then offer to configure the connection to the printer. Select “Wi-Fi connection”.
  • Further, all the instructions will appear on the screen-you will need to press the Wi-Fi button on the printer, wait for the indication, after which your computer will “find” the printer and pass it to the Wi-Fi connection parameters to connect with the router.
  • If there were no problems on the 4th step and the connection was not possible, try to select the Wi-Fi connection again, but using the WPS button on the router (the instructions will appear in the program). Cm. What is WPS button on a Wi-Fi router.
  • If this method does not work, you can connect to the printer by USB and then perform wireless connection settings using the same program.
  • At the final stage, if desired, you can set a static IP for the printer by selecting instead of DHCP manual IP address tuning (in some cases it may be useful). Indicate the address located in the subnet of your router (for example, if the address of the router 192.168.one.1, you can indicate something like 192.168.one.100).

The connection is completed on this (you will be asked to download additional Epson programs, optional) and you can work with the printer on Wi-Fi.

The remaining computers in the same network, as well as mobile phones with an installed Epson IPRINT application, are usually automatically found a printer, but for computers I recommend repeating the installation of drivers (for the possibility of setting up printing, as well as scanning over the network if you have all-in- One Printer).

There is a simpler (partly) method of connecting Epson printers to Wi-Fi-press and hold the Wi-Fi button on the printer until the indicator begins to flash the left and right part nearby, and then press and hold the WPS button on the router (then release it (then release ). The printer must connect automatically, while the Wi-Fi indicator will stop flashing, but it will just burn. After that, you will need to add a network printer on the computer. But I recommend the option described earlier.

How to connect Canon printer by Wi-Fi

For printers and All-in-One Printer Canon, in general, there are the same methods of connecting by Wi-Fi (I recommend using the second):

  • Click Hold the Wi-Fi button (on some Canon printers the WPS signature) on the printer until the orange indicator blinks, release it. Then press and hold the WPS button on the router, the connection will be installed automatically after a while (the Wi-Fi indicator on the printer will stop flashing and will just glow). After that, you will need to connect the network printer by Windows or other OS.
  • Connect a computer or laptop to the same Wi-Fi network to which you plan to connect the printer and go to the website https: // www.Canon.RU/Support/Consumer_products/Product_ranges/Printers/Pixma/. Select your printer model or All-In-One Printer Canon, download and install the proposed branded program that will lead you through all the steps of the Wi-Fi connection settings (and download the necessary drivers).
  • For printers and All-In-One Printer Canon stores Play and Apple App Store Appendix Apple Apple access (as many as two of its options for different printer models), which allows you to configure the printer connection by Wi-Fi to your router or directly To the mobile device (in the application, click on the “Register the Printer” icon, then. “Follow the wireless network”, “Selecting the connection method”, and then, after about a minute search for the connected printer, when it is not found, in accordance with the instructions in Appendix).

I hope the instruction helped you connect the printer by Wi-Fi. If something does not work out, leave the Комментарии и мнения владельцев-perhaps there is a solution.

Epson L355 Wi-Fi Settings

The procedure is quite simple, you just need to follow the presented instructions:

  • Open the control panel.
  • In the control panel, select the center of control of networks and total access, then the item “Management of the wireless network”.
  • Then, in the dialog box that opens, select the “Add” item
  • Then, in the manual creation of the connection to wireless networks, we create a computer “computer. computer” network and select “Next” item
  • In the dialog box we introduce the name of the network, at will.
  • Then, in the new list of safety type, select “Without checking the authenticity of Open”, then put a box at the item ”Save the parameters for the network” and “Next”.
  • Then click the “network (network name) is ready” and close the window, turn on the printer.

After the settings are completed, you can proceed to the printer settings.

  • On the inclined printer, select the “Settings of the Wireless LAN” menu and click “OK”.
  • Then, on the control panel, select the settings wizard menu and click “OK”. We are waiting for the master to find all available wireless networks.
  • Then we find, a previously configured network with your name, select it.
  • The printer will connect to the network and request a command on printing reports of the connection done.

How to connect Epson L366 by Wi-Fi using the built-in installation master?

What you need to know before starting up:

After creating a wireless tuned network using a router, you must go to work on the printer settings. To do this, you need to go to the menu “Setting and select the parameter” Network. Further, the setting master will display information about available networks for connecting. Next, you need to choose the name of your created network. If the printer cannot find the required network, then its name must be prescribed manually, taking into account the registration register. Having selected the desired network, the printer will request a WEP encryption key or WPA password. They are also introduced taking into account the register. The printing device is connected to a wireless network and now you can send various tasks for printing.

Thus, connecting the printer to Wi-Fi will not take much time. The connection process takes only a few minutes. The main thing is to prepare for work, having previously found out whether the equipment supports the required technologies and, of course, have a Wi-Fi working and configured network with a pre-well-known password and name.

Installation of Wi-Fi compounds

A wireless connection to a local network is installed using Wi-Fi Protected Setup (WPS) technology. It allows you to add a new network device in one of two ways:

In the first case, it is enough to press and hold the Wi-Fi button on the front side of the All-In-One Printer Epson for three seconds. When the first two LEDs begin to turn on alternately, click “WPS” on your router. With a successful installation of the connection, the operating mode of indicators will change. They will turn on and turn off at the same time.

If there is no “WPS” button on the router, use the second network connection method. Check PIN on the bottom panel of the Epson printer. The desired code consists of eight digits, divided by a hyphen into two blocks of four characters. You can find it in the last line of information on the sticker, under the serial number and MAC address All-In-One Printer Epson.

Open the router of the router in any browser. The standard entry data can be found on the sticker at the bottom of the device. To go to the administrative panel, enter the specified IP in the address bar. In the authorization window, indicate the login and password from the router. Go to the “WPS” section and click on the link to add a new device. Enter the PIN code specified at the previous stage.

note! In some models of routers, this menu may be called “QSS”. It is also possible to use the full name: Wi-Fi Protected Setup.

Press Settings by Wi-Fi

When the EPSON printer connection to the local network is completed, go to the installation of software on the devices from which the seal will be performed. For computers or laptops on Windows, install the printer driver, the disk with which is included. You can also use the built.in system tool to search for. On mobile devices, use the Epson Iprint application.

Insert a drive with a driver and run the installation file. In the absence of a disk, the utility can be downloaded from the official EPSON website. During installation of the application, select “Wi-Fi connection” to add a network printer. You can also install the driver through the Windows control panel in the “Device and Printer” menu.

Press Settings by Wi-Fi

After connecting the Epson printer to the local network, proceed to install the software on the devices from which you will print. For computer or laptops Windows, install the printer driver from the attached CD. You can also use a built.in system tool to search for software. Use the Epson Iprint application on mobile devices.

Insert a drive with drivers and run the installation file. If you do not have a disk, you can download the tool from the official EPSON website. When installing the application, select “Connect through Wi-Fi” to add a network printer. The driver can also be installed through the Windows control panel in the “Device and Printer” section.

Printing from a mobile phone or tablet

The IPRINT application is designed to connect and print on smartphones or tablets. The version for iOS can be downloaded in App Store, Android tool is available in Google Play. This is free for both mobile platforms. Windows tablets use the same configuration system as computers.

Tip! In the case of mobile devices with iOS (iPhone or iPad), you can print documents without installing the application. This uses a standard Air Print technology.