How to log in to the router from your phone. Setting up wi-fi on your router from your phone or tablet

How to enter the router settings?

What would go to the settings, we need to write in the address bar of the browser IP-address of the router 192.168.1.1, or 192.168.0.1, and go to it by pressing Enter. A window appears requesting a username and password. Again, the defaults are usually admin and admin.

TP-Link settings can even be accessed from a tablet, or smartphone, through the TP-Link Tether app (but can also be accessed through a mobile device’s browser). But I recommend using a computer (laptop). Open any browser and go to 192.168.1.1, or 192.168.0.1. It depends on the router model.

Why do I need to go into the router settings from my phone?

Wi-Fi is now present everywhere. at work, in recreation, in stores. It makes life easier because anyone can access the internet instantly. Many people connect Wi-Fi routers in their homes and apartments, allowing them to have their own wireless local area network.

Setting it up over the phone is not much different from the computer settings. As a rule, the same address. “192.168.0.1”. Logging in from your phone doesn’t require a wire, which is required for a PC. It will be replaced by Wi-Fi. The first thing to do is to activate wireless connections on your gadget, if this has not been done before. From the phone this function is available through the notification panel.

How to share the Internet from your phone on the router?

How to distribute Internet from the phone through the router?

  • Enter “Settings” menu.
  • Find “” button and press.
  • On the new page, select the item “Modem mode and access point”.
  • Tick the “Portable Wi-Fi hotspot” box.
  • In the same window, tap the “Settings” section.
  • Fill in the fields:
  • Press “Save”.
router, your, phone, setting, wi-fi, tablet

How to connect to Wi-Fi from phone to phone?

How to connect Android smartphone as USB modem

  • Connect your phone to your PC via USB. If this is a new device, wait until the drivers are installed.
  • Open the settings of your smartphone. Under “Wireless Networks” (“Network”) find “Modem Mode” (“Modem and Access Point”).
  • Activate USB-modem.

Logging into your Netgear router: how to log in and change settings

In this Netgear router login guide, we’ll show you how to log in to your router and what settings you should configure to ensure the fastest and most secure wireless Internet speeds possible.

Maybe you bought a Netgear router, set it up, and since then you’ve had no reason to go back to the router setup or configuration menu. And now you need to go in again to change something. Maybe you’ve been using the same broadband provider for ages and finally decided to switch to a better deal. But you’ve completely forgotten how to log in to the Netgear device.

This article is for those who are in this or a similar predicament. Whatever your reason for wanting to log into your Netgear router, we’ll show you how to do it in simple, straightforward steps.

After that, we’ll take some time to go over some common settings that you might want to adjust when you enter the router’s menu, such as setting QoS settings.

There are two basic ways to log in to your Netgear router: either from a PC using a web browser, or from your phone (or tablet) using a special app.Let’s look at these options in this order.

How to log into your Netgear router from a PC

The usual way to log in to your Netgear router (Image courtesy of Netgear) (Image courtesy of: Future)

The method of logging in to your Netgear core router

First of all, you need to open your favorite web browser (it doesn’t matter which browser, any browser will do). Then simply type the following into the address bar (URL) of your browser and press Enter:

After that, you should see a router login window asking for your username and password. If so, skip to step 3. If your router’s login window doesn’t appear, skip to step 2, which is an alternative method of logging in.

Note that Orbi network routers use http://www.orbilogin.net or http://www.orbilogin.com.

This is an alternative way to login to the Netgear router (Image courtesy of Netgear)

router, your, phone, setting, wi-fi, tablet

2.An alternative method of logging in to your Netgear router (via IP)

Alternatively, you can enter the IP address of your Netgear router in the URL bar of your browser.

The IP address is. is a four-digit number with dots between each number, and you can think of it as a numeric address that shows where your router is on your local network. Usually it will be something like 192.168.xxx.xxx. where the last two numbers (xxx) can be slightly different.

This IP address might be written down somewhere in your router‘s instruction booklet, but if not, you can find it out quite easily from your computer.

On Windows 10, go to the search box (next to the “Start” button), type ” C ” and sentences beginning with the letter “C” will appear above: click “Command Prompt”. (In earlier versions of Windows, click Start, click in the search box. Or on the magnifying glass icon. type cmd. then click Command Prompt).

The following window will appear. simply type the following into this window (known as the command line) and press Enter:

A string of numbers will appear below.Note the one labeled “Default Gateway” (usually at the bottom).

Just type that number as it’s written (including the dots between the numbers) into your browser’s address bar, and you’ll be golden.

Enter your username and password to log into your Netgear router (Image courtesy of Netgear) (Image courtesy of: Future)

Enter your user credentials

In the Netgear router login window, which asks for your username and password, enter your credentials, then click “Login,” and you’re done. you have successfully logged into your Netgear router.

Now you can skip to the section (optional) at the bottom of this article on general settings to look right into your Netgear router menu.

There is one potential stumbling block here. If you have forgotten your username or password. You changed it from its default value, right. or at least the password?

These default values are. The username is “admin” and the password is “admin”. “password” (these default values are written somewhere on the bottom of your router). but since they are so insecure (and known to everyone) you should always change them

However, if you don’t know what your password is, you can try these defaults just in case. Just don’t forget to change it later. Otherwise you will need to reset your password.

Recover your password (Image courtesy of Netgear)

Restore password

At the Netgear router login window, which asks for your username and password, click Cancel. Now, if you previously enabled password recovery, the router‘s password recovery screen will appear.

You’ll need to enter the serial number of your router (it’s written somewhere on the device, probably on the back) and answer a few security questions. Once that’s done, you’ll be shown the password.

If you didn’t enable password recovery or forgot the answers to the security questions, you’re out of luck. You’ll just have to start from scratch by performing a factory reset of your Netgear router, which will reset your username and password to defaults (as described above).

To perform a factory reset, make sure the router is turned on, then locate the reset button (it will almost certainly be on the back of the device). This is a small hole where you need to insert a paper clip and push it in for seven seconds (maybe a few more for more precision).

The router will reboot, but note that you will lose all your settings (you will need to configure the device again from scratch).

Logging into your Netgear router through the mobile app

The Netgear app lets you log into your router (Image courtesy of TechRadar / Shutterstock)

How to see who is connected to the router?

In the settings, go to the “Wireless” tab (wireless mode). If you have a dual-band router, then open the tab with the desired network (2.4 GHz, or 5 GHz). And go straight to “Wireless Statistics” (wireless statistics). The table will display all the devices that are connected to your Wi-Fi.

How to see who is connected to my Wi-Fi router?

router, your, phone, setting, wi-fi, tablet
  • You can just go to the Wi-Fi router settings panel, and see the information we need.
  • So the most important thing is to get into the settings of the router
  • You will get to the management page of the router
  • Click on the “DHCP” tab, then “DHCP Clients List.

How do I know who is connected to my Wi-Fi?

In the settings, go to the “Wireless” tab. If you have a dual-band router, open the tab with the network you want (2.4 GHz, or 5 GHz). And go straight to “Wireless Statistics” (wireless statistics). There in the table will be displayed all the devices that are connected to your Wi-Fi.

Well, and just in case, I’m giving you a link to the article if you can’t get to 192.168.1.1 (or 192.168.0.1). In the control panel, go to the Wireless tab. Wireless Security. In the Wireless Password (PSK password) field you will see the password for your Wi-Fi network.

How to enter the router settings from the phone

  • Plug your ISP’s cable into the router‘s port called WAN or INTERNET. It is often highlighted in a special color and different from the rest of the ports (LAN):
  • Turn on the Wi-Fi on your phone. To do this on your iPhone, go to “Settings”, select “Wi-Fi” and turn it on: Although, on modern iPhones Wi-Fi is always enabled by default and you are unlikely to need this item. In Android, pull the curtain, press and hold your finger on the Wi-Fi icon: and just make sure it’s turned on:
  • Connect to the router’s network. Different router manufacturers will call their network differently: D-Link may have dlink or, for example, dir300nru; modern TP-Link’s default SSID will be something like TP-LINK_A0816A (where the second part of the name is the last 6 characters of the MAC address).
  • Enter your Wi-Fi network password (t.н. Security key) and click “Connect”: Here again, it depends on the manufacturer. If you have a TP-Link router, use the PIN on the sticker: If the default network has no password, then you will connect without entering the key.
  • Important! Now turn off the mobile Internet on your phone, because if the Internet on the router is not yet configured, your phone will try to access the network via mobile data and you will not be able to go to 192.168.0.1:
  • Open the browser on your phone. For example Chrome.
  • Enter the IP address or site name of the router that is on the sticker into the address bar and press enter. For example http://192.168.0.1 Warning! If you can’t access the settings from the IP address printed on the sticker, check out our article How to get the IP address of your router from your phone.
  • Enter your username and password from the same sticker and press Login or LOGIN. Make sure you enter the login info with a small letter: On old TP-Link router firmware the login window may look like this: If you successfully enter the router’s settings from the phone you should see this screen:

After changing such settings as network name, network security key from your phone (iPhone or Android), you will have to reconnect to the network each time. I recommend this sequence of actions:

  • Go to Wireless mode.
  • Change the name of the Wi-Fi network to your own.
  • Click Save.
  • Reconnect to the network with the new name but using the old password (in our case the password from the sticker).
  • Go to the settings again with the same address (e.g. 192.168.0.1).
  • Go to the “Wireless security” section.
  • Select WPA2-PSK security type.
  • Set the AES encryption algorithm.
  • Enter your PSK password (aka “Wi-Fi password” and “wireless security key”):
  • Click Save. You will disconnect from the network again.
  • On your phone, find your network in the list. Click on it and enter the new key you just installed. At this point, you may encounter an error where your smartphone or tablet will stop connecting to the network and it will say “Saved”, “Authentication” or “Authentication Error” under its name:

In this case, long press on the name of the Wi-Fi network and select “Forget network” or “Delete this network”: The network profile with the old password will be deleted from the phone, you will be prompted to enter the password and you will be able to connect normally: