How to stick a protective film on the tablet correctly

Protective film for the tablet

Technical progress that occurred at the beginning of the 21st century brought to our world many new digital and computer devices. Stationary computers were replaced by more advanced and small.Sized laptops and netbooks, which, in turn, handed over the baton to smartphones and tablets. However, with the advent of sensory screens, the problem of protecting them from scratches and other damage during operation arose. A protective film for a tablet and a smartphone, respectively, was invented on this subject.

The protective film is a very thin polymer coating, which, as a rule, is covered with special glue, depending on the scope of use, on two or one side. Films are different in structure and appearance, for example:

A protective film itself is a very useful and universal accessory for any device with a touch display and ordinary glass. Different in the structure of the film can withstand various mechanical damage from the usual scratching key or the stylus to protection from the blow when falling on the display. Unfortunately, the lines of operation of the films are limited, so after two or three months of a careless attitude it will have to be changed. If the device is good, then it will last up to a year.

stick, protective, film, tablet, correctly

Usually after several months of use, to return the normal state to return, you just need to remove the old film and stick a new one. But at this stage there are many problems that ultimately lead to corruption of the protective coating.

Why do you need to remove the protective glass from the phone

Protective glasses for smartphones are designed to save the display from strikes, chips, cracks, scratches and other damage. Therefore, do not be surprised that the glass is subjected to strong wear and tear during the use of a mobile device. Thus, there is an urgent need to replace it. However, replacing the protective glass of a smartphone may be required for other reasons. The most basic ones should include the following cases:

  • Distance of glass coating. If the user often wears a smartphone in a or in a small handbag where the device is in contact with various objects (keys, coins, etc.D.), then over time, the coating of protective glass is erased. Scuffs, scratches and “rainbow” divorces begin to appear on it. Similarly affects the quality of the image very negatively. Therefore, it is advisable to replace such glass.
  • Glass damage. The most common problem that can only be eliminated by replacing the accessory. Cracks and chips on glass can be easily formed when the mobile device falls or hit. But replacing protective glass will cost cheaper than a phone display.
  • Flasping of glass. Basically, a similar problem applies to inexpensive protective glasses for a smartphone. Under various circumstances, the protection begins to exfoliate. Air bubbles may occur, under which dirt and dust are clogged. A similar defect clearly spoils the appearance of the screen of the mobile device. Therefore, it is recommended to replace glass.
  • Replacing protective glass. In some cases, the consumer may wish to replace the protection. For example, to change the usual film to a protective glass or install glass with any effect.
  • Cleaning the main glass smartphone. Basically, a similar procedure is done before selling a mobile device. Although it is not rarely owners of smartphones that notice the accumulation of dirt along the edges of the glass, as well as in the connectors for the speaker, camera and functional buttons.
  • Repair of a mobile apparatus. If the telephone, smartphone or tablet got into the service center, then upon the return of Davais, the owners do not rarely change the protective glass, since after the service it may look inappropriate (often the services themselves offer a paid replacement of the protective glass of the smartphone).

As you can see, there are many reasons for replacing protective glass, under the influence of which the owner of the gadget decides on a similar procedure. At least the process of removing the protective film is not a supercomplicated task. But still it is necessary to take into account some risks that may occur when removing the protective coating of the smartphone.

Rules for sticking the film

Sit for several hours on the Internet or walking on branded stores in search of a suitable protective film is still half the age, but how to stick a film on the tablet without ruin it, this is really a test, which not many owners of gadgets are being decided and prefer to use the services of professionals.

Preparatory stage

First of all, it is necessary to properly prepare the surface of the screen, since dust surrounds us everywhere and get at least one small dust on the screen during gluing. This will ruin the appearance of the device and, of course, will spoil the owner’s nerves when it is removed.

Therefore, first we wash our hands with soap to remove fat and garbage as much as possible from the skin, which are 100% present on the hands. Now it is recommended to go to the bathroom, where the humidity of the air and dust particles will be “nailed” to the floor. Many experts advise in front of the gluing process to turn on hot pressure of water so that the room is saturated with a couple, then you can begin to glue the procedure.

Wipe the surface of the display only with a special cloth that does not contain a pile. You can slightly moisten the napkin with water (a couple of drops), from this, the protected tablet will not suffer, and dust and other garbage will be well removed.

Preparation of the film

Here you need to be very neat, because the film has two varieties:

In principle, there is nothing complicated in fitting the film for specific sizes. Just take the ruler to measure all sides of the tablet and cut the resulting rectangle.

Absolutely all protective films have a transport surface, which protects the adhesive coating from garbage and serves as a convenient tool for neat cut, as a special dimensional grid is applied.

Sticker process

As mentioned above, we go to the prepared bathroom, many experts also recommend buying a special spray can with compressed air, which can be used for contactless dust removal is very convenient and useful.

If there is no at hand, then this step is not a problem is exclusively advisory in nature. We take the film and disconnect the upper transport film literally by 2-3 centimeters and attach the side to the screen with the “sticky”: we align the corners and direction so that it is parallel to the tablet itself.

Now using the fingers, and best of all, we start one, or even half a centimeter, “glue” the film to the surface of the screen, using it as a spatula. If something goes wrong, you can calmly peel off and repeat everything again, the main thing is that during these manipulations the dust does not reach the goal.

At the end, in most cases, bubbles should not appear, but everything happens. Therefore, we take the card and carefully begin to squeeze the bubbles closer to the edges of the film, small bubbles will disappear over time themselves.

The final stage

After the film is completely glued, you can once again wipe the already protected tablet with a napkin to remove the remaining traces of the prints or the dust that has already hit.

If in the process the dust still got on the screen or on the film, do not panic and immediately run to buy a new. Turn on the tap and gently rinse the surface under running water, then dry it and you can start again to the procedure.

It is important to know that the adhesive surface from water does not lose its properties, especially since most of the films are attached to the screen due to statics, and not on some special glue.

In principle, high-quality and expensive film should withstand reusable peeling and gluing, but still try to attach it to the screen at a time or maximum twice, then it will not lose its protective functions.

Some recommendations

Most likely, many owners heard about such a method as wet gluing, which suggests:

This method has a number of advantages. This is when removing water, accidentally falling dust will leave it with it, the clutch with the screen will be more rigid. But unfortunately, this method also has disadvantages. With careless circulation, drops of water can safely get into the middle of the device and then, after the contacts closed the device, it remains only to throw out. Therefore, beginners are strictly forbidden to use this method if you have a large supply of tablets and films, then train.

The most ordinary film will last about a year, if you use it carefully, then more, but the price is constantly falling, so in a year you can change it without a twinge of conscience for a new one.

Prepare the phone for sticking the film on the display

Before sticking the film on the display of the mobile apparatus, it needs to be thoroughly wiped from dust, dirt and fat stains from the fingers. If there is a cleaning one, then it is imperative to process the glass of the phone display. Only after it you need to re.Dry the display (this is why two microfiber napkins are needed). So as not to stain the screen again, put the device on the table and hold it by the tank panels.

How to stick a protective film on a smartphone [Instruction]

As a rule, people take care of the body of their phone, but for some reason forget about the protection of the screen. To do this, not only covers with the front cover were invented, but also ordinary films that glue on the screen and perfectly protect it from scratches. It would seem that this is such a simple accessory, but you need to work hard to stick it correctly and gently. Today we will tell you in detail about this.

So, first of all, take the phone in the hand and thoroughly wipe the smartphone screen so that it does not have dust dust, fingerprints, crumbs, etc.P. It is especially necessary to pay attention to the presence of dust, because it is the main obstacle to the successful gluing of the film. To achieve complete disappearance of dust, you must wipe the screen with a bottomless cloth. Sometimes you can use a little water and a special product, but keep in mind that household cleaning agents should in no case be used for screens. Also undesirable for use of alcohol.Based or alcohol itself are undesirable. The napkins that are designed to clean LCD monitors are ideal.

After the screen is properly processed, remove the film from the packaging. There should be a paper petal on one of the edges of the film. Then put the film on the table or any hard surface and press with force on the petal. This will allow you to separate the thin protective film from the transportation. At the same time, remember that you can not touch the inside of the film. And do not open the entire film from the transportation. It is best to take a transport film a little along the entire length, and then attach a protective film to the smartphone display. It remains only to push the fingers over the entire surface of the film, so that it sticks more tightly to the screen of your phone. If you did not succeed the first time, you can do the operation from the very beginning.

Often when gluing the film, bubbles appear. To get rid of them, it is enough to spend several times up and down a credit card on the film and the bubbles will immediately leave. If this did not help you, then your low.Quality film. And not only is it not able to protect the smartphone screen as much as possible, such an accessory will not last long.

Process

Let’s move directly to the process. We take out a film and look for a petal on it from the number “1”. It is this part that is not glued, although it seems in appearance the other way around. In order to separate the transport film, you need to squeeze this angle with force.

Dividing the film until it completely separates it. Also be especially careful not to touch the inside of the target film.

Why glue the protective glass on the smartphone display

Many consumers began to abandon the gluing of protective glasses on the screen of modern mobile devices, due to the fact that they have excellent protection without this accessory. It is worth noting that there is a share of truth in this. After all, smartphones (especially flagship models) are equipped with super.Duty hardened Gorilla Glass Glass. Displays with such protection are actually not afraid of scratches, dust, as well as fat divorces left by fingers. In addition, marketers of mobile phone producers tried to advertise this feature well. In this connection, many consumers began to reliably believe in the invulnerability of their Daivas. Nevertheless, in practice, everything is far from as good as the developers say about this. Displays protected by Gorilla Glass, you can still scratch or break. Therefore, some owners of smartphones are still resorting to gluing additional protected glass.

The instructions for the sticker of protective glass on the phone screen are almost no different from the similar guidance regarding the gluing of the protective film. But the difference is still available. Since glass is characterized by high rigidity, it is advisable to have several additional tools for gluing it. It is worth noting that the whole process of work consists of several main stages. In particular, we are talking about the following points:

Choosing and buying protective glass

This stage should be approached very responsibly. After all, if you acquire an inappropriate accessory, you will have to spend money again on a new protective glass. There are several different types of protective glasses for a smartphone display. Therefore, you need to choose exactly the one that is best suited to the model of your mobile device. Choose carefully so as not to buy an accessory with an unnecessary effect. Read more about this in the article “How to choose a protective glass for your phone”.

Preparation of the workplace and smartphone

Before starting work, it is necessary to carefully prepare the mobile device and the place itself where the glass will be glued. A spare protective glass, two microfiber napkins (one wet, second dry), a special holder, tape and cleaning should be prepared in advance. It is recommended to work in a clean room so that the dust does not settle on the display of the mobile apparatus during gluing. It is even better if the workplace is equipped with a full.Fledged air ventilation system. As for the phone, before gluing the protective glass, its display should be thoroughly wiped. Immediately cleaning should be carried out with a soft cloth with a cleaning product. Then additionally wipe the dry microfiber dry.

Gluing protective glass on a smartphone

Do not rush to tear the film from the protective glass and glue it to the display. To get started, just fit the product to the screen to see if it is suitable for your mobile phone. In addition, you need to try to remember the approximate location of the protective glass on the smartphone display. If you do not want to remember, then glue the glass with tape to the side panel (or special stickers from the set).

Attention: We do not recommend very gluing adhesive tape to the body of mobile. Otherwise, when it is peeled off, you can damage the paintwork of the gadget. To do this, better use a special silicone holder.

As soon as you determine the approximate location of the protective glass, you can proceed to gluing it. Although for starters, wipe the display again with a microfiber (this time you can dry). Tear off the film from the protective glass and move on to the process of gluing the spent accessory. The sticker is carried out by applying glass to the display, in parallel on the entire plane (it is not recommended to bend the protective glass). In case of failure, you will have about 5 seconds to quickly tear off and cross the protective glass. That’s the whole instruction.

How to stick a protective film on the tablet [Instruction]

It often happens that after buying a new tablet or smartphone, the question arises about protecting the gadget from scratches. If in order to protect the case itself, you can only buy a case, then special films are sold for displays. It seems to be a simple accessory, but sometimes not many manages to stick it at times. In most cases, after the film is glued, bubbles with air begin to appear, which are quite difficult to drive out of the film. However, such problems most often arise if the user acquires a cheap film. With expensive high.Quality films, the situation is much easier and the bubbles do not seem a huge problem.

Ochranná fólie ScreenShield: Jak ji aplikovat na smartphone (how to apply a screen protector)

But even an expensive film needs to be able to properly glue, about this we will tell you today.

When gluing the film on the tablet, the main task is not only that gluing it evenly, but also avoid the appearance of bubbles. The latter, in turn, arise due to the fact that dust accumulates on the screen. Thus, before gluing a protective film, it is necessary to clean the tablet display from dust particles. It is best to do this in the bathroom so that the dust settles with moisture. As a material for cleaning, you can use a microfiber rag. At the end of the operation, make sure that the surface of the tablet screen is completely dry. After that, in order to maximize the particles of dust, which still remain even after wiping with a rag, take paper tape and glue it on the display. We tear off and get a perfectly clean surface.

How To Perfectly Install ANY Screen Protector Without Bubbles!

Instructions in pictures how to correctly stick a protective film on a tablet:

Now you can start gluing a protective film. When you separate the film from the transportation, try not to touch the inside of the film, and you should also not completely tear off the film from the transportation. Further with neat slow movements you need to attach a film, starting from the edge of the display. Then you can use a plastic card to drive it on the film, smoothing it. If you have bubbles, then do all the actions from the very beginning. In addition, dust can fall on the inside of the film. To remove it, you need to use paper tape in the same way as we did above in relation to the screen.

We glue the protective film without bubbles on the tablet

The sequence of work on gluing the film on the tablet is as follows:

  • If you decide to stick a protective film, then first wash your hands thoroughly, washing away any dust or fat from them.
  • Look at the tablet screen. If the tablet was already in use, then you need to wipe the screen with a special composition using a clean napkin without a pile. The screen should be absolutely clean.
  • Unpack the packaging with a protective film. It is protected by another layer (layer 1), which does not need to be removed right away. Bending a little layer 1, we begin to stick the film on the wide side of the screen. You should not drive a film under the very edge of the screen: half a million can be left.
  • Using a plastic card, gradually glue the film, exposing the air from under it with a card using a card like a spatula.
  • Having glued the film on the entire surface of the screen, once again walk along it with a card and fingers, expanding the air bubbles, if any.

If something did not work out, then it is not difficult to remove the protective film and glue it again. To do this, you need to pick up the edges of the film with something and just remove it from the screen.

When working, you need to ensure that fingerprints do not remain on the sticky surface of the film. As, however, on the tablet screen.

Thanks to the protective film, the screen will remain clean for a long time.

Video on how to stick a protective film on the tablet correctly