How to use a router as a Wi-Fi receiver

Is it possible to use a router as a Wi-Fi adapter: Instruction

The essence of the settings is that the router becomes a kind of wireless adapter. He ceases to give out wireless communication that he receives via an Internet cable, but, on the contrary, accepts and transmits it to other devices, such as personal computers or laptops, Smart TV using a network cable.

When setting up the main access point, no parameter can be touched except a specific Wi-Fi channel, which will help to avoid upcoming difficulties in organizing a network associated with scanning of operating frequencies in automatic mode.

After that, a router acting as a client is taken and put as the main device that distributes wireless Internet in a house or apartment. Then it is connected to it with a cable and the wireless Internet is organized, despite the fact that at first the router has only one LAN port for wired connection.

Guest Wi.Fi

You often have guests who ask to connect to your home wi.Fi? Why not allocate their own network to them? To do this, connect your old router to the main router by wire or Wi.Fi.

Then configure it so that it distributes a signal. You can not assign a password at all or make a simple password for guests. If desired, it can also limit the speed so that friends do not abuse your channel.

Network setting on a computer

I recommend this step only if we cannot go into the router settings that are described below.

router, wi-fi, receiver

We click the “Start”, we find the “control panel”, after which the “Center for Control of Networks and General Access”.

With the right button, click on the active adapter and click on the “properties”.

The window may have another look, to change the view, click on the torn list of the “View” category and select “Small Bades”.

In the case of Windows 10 or 8, 8.1 can be done differently, just click on the “Start” mouse or the Windows icon, which is in its place.

router, wi-fi, receiver

In the menu, select the “control panel”. Further actions are similar to the described above.

So, you need to click on the “Changing of the parameters of the adapter”.

Share USB Modem Internet Via Wi-Fi Router �� How to use USB Dongle data via WiFi Router | Som Tips

We highlight the connection protocol version 4 (TCP/IPV4) for the Internet, click “Properties”.

We set the receipt of IP addresses in automatic mode, similarly repeat the setting if there are other connections, both on local and wireless network.

We use a router as a Wi-Fi receiver for connecting a Wi-Fi Internet TV

Hey! In this article, I promised to talk about one interesting scheme that can be used to connect a TV on the Internet on a wireless network.

I will quickly tell you what the essence of this method is and in what cases it can be used. Well, then, let’s start setting up.

This method will come in handy when there is no built-in Wi-Fi receiver in your TV, in which case, the TV can be connected only via network cable. But, you do not want to stretch out the cable from the router, or it just fails.

See also  The TV doesn't connect to Wi-Fi

Yes, you can buy this same company, external Wi-Fi receiver. But it costs twice as much as a simple router. But I am still inclined to the fact that you will use this method in the case when you already have a router, which is just standing idle.

Or for example, the signal of your Wi-Fi network does not catch in the place where the TV is worth. Yes, in this case, you can buy a Wi-Fi Repiter that will enhance the signal of your wireless network. But an ordinary router can be configured as a repiter.

We will take a router (which for example, you have dust somewhere in a locker), install it somewhere near the TV, and set it up in a repiter mode. Then, from this router we will connect the network cable to the TV. That’s the whole scheme.

Now a little more.

So, we take our router and install it near the TV. I have this TP-Link TL-MR3220, I have been standing idle for a long time. It is not necessary to install it near the TV itself, for example, even somewhere on the floor, the bedside table.

We turn on the router in the outlet (you can not connect to the TV yet). The main thing is to configure the router in the repiter mode. We need that he would take the Internet from your main router and hand it to TV. We set up everything according to this instructions. Https: // f1comp.Ru/internet/kak-nastroit-besprovodnoj-mosts-mosts.Mezhdu-dvumya-wi-fi-routrami-router-kak-commere-t-rout-tp-lines/.

And only after this router (which we put near the TV) will be distributed to the Internet, we move on to the second step. To check, just connect a laptop, or phone. If the Internet works, then you can connect the TV. If all the same, you were not able to configure the bridge mode, then you need to remember that not all routers can work in this mode with each other (I’m now about the unresponsibility of the devices). It’s good when both devices are from one company, then there is more chances to make them to make them.

If you succeed, then we connect the TV via a network cable.

Or connect the Wi-Fi TV if there is such an opportunity (for example, if you put a second router to strengthen the signal from the first).

That’s actually the whole scheme. I hope someone will come in handy!

And I apologize for the quality of the photo. In the near future I will try to buy a normal camera, otherwise I take pictures on the phone, and with poor lighting, the quality of the photo is not very.

We use a router as a Wi-Fi receiver for connecting a Wi-Fi Internet TV

Hey! In this article, I promised to talk about one interesting scheme that can be used to connect a TV on the Internet on a wireless network.

I will quickly tell you what the essence of this method is and in what cases it can be used. Well, then, let’s start setting up.

This method will come in handy when there is no built-in Wi-Fi receiver in your TV, in which case, the TV can be connected only via network cable. But, you do not want to stretch out the cable from the router, or it just fails.

Yes, you can buy this same company, external Wi-Fi receiver. But it costs twice as much as a simple router. But I am still inclined to the fact that you will use this method in the case when you already have a router, which is just standing idle.

See also  How to connect a laptop to a Wi-Fi router

Or for example, the signal of your Wi-Fi network does not catch in the place where the TV is worth. Yes, in this case, you can buy a Wi-Fi Repiter that will enhance the signal of your wireless network. But an ordinary router can be configured as a repiter.

We will take a router (which for example, you have dust somewhere in a locker). Install it somewhere near the TV, and set up in the repiter mode. Then, from this router we will connect the network cable to the TV. That’s the whole scheme.

Now a little more.

So, we take our router and install it near the TV. I have this TP-Link TL-MR3220, I have been standing idle for a long time. It is not necessary to install it near the TV itself, for example, even somewhere on the floor, the bedside table.

We turn on the router in the outlet (you can not connect to the TV yet). The main thing is to configure the router in the repiter mode. We need that he would take the Internet from your main router and hand it to TV. We set up everything according to this instructions. Https: // f1comp.Ru/internet/kak-nastroit-besprovodnoj-mosts-mosts.Mezhdu-dvumya-wi-fi-routrami-router-kak-commere-t-rout-tp-lines/.

router, wi-fi, receiver

This is interesting: the phone (tablet, computer) is connected to Wi-Fi, but the Internet does not work. Sites do not open

And only after this router (which we put near the TV) will be distributed to the Internet, we move on to the second step. To check, just connect a laptop, or phone. If the Internet works, then you can connect the TV. If all the same, you were not able to configure the bridge mode, then you need to remember that not all routers can work in this mode with each other (I’m now about the unresponsibility of the devices). It’s good when both devices are from one company, then there is more chances to make them to make them.

Or connect the Wi-Fi TV if there is such an opportunity (for example, if you put a second router to strengthen the signal from the first).

That’s actually the whole scheme. I hope someone will come in handy!

And I apologize for the quality of the photo in the near future I will try to buy a normal camera, otherwise I take pictures on the phone, and with poor lighting, the quality of the photo is not very good.

We use the TP-Link router as a “Repiter

So on our main router, only the channel needs to be changed.

Setting up the main router

Go to the router settings and go to the Wireless tab. Opposite the Channel parameter, set the channel number, for example 6 (the same channel will need to be installed on the router, which we will configure as a repiter). Save the settings by pressing the “Save” button.

Setting the router “Repiter”

At the time of configuration, a router (which will work as a repeater) must be connected to the computer via cable.

We go into the settings of the router. To do this, in the browser we type the address 192.168.0.1, or 192.168.One.1 (the address can be viewed from below the router).

Then there will be a request for entering the login and password for access to the settings of the router. If you did not change them, then usually by default it is Admin and Admin (you can also see below the device).

Read more about WPS I wrote in the article what is QSS and WPS? What is the QSS button on the Wi-Fi router and how to use it?, You can read. We need to turn off this function.

See also  How to enable developer mode on your Samsung

To do this, go to the WPS tab and click on the “Disable WPS” button.

Reload the router. To do this, you can click on the “Click Here” link that will appear on the page after changing the settings.

After rebooting, a page with a router should be opened again.

Change the IP address of the router TP-Link

Go to the Network. Lan tab. In the IP Address field, change the last number of IP addresses to number 2. For example, I had an address 192.168.0.1, and I changed it to 192.168.0.2. To save the settings, press the Save button.

The router himself reboot, he will ask to enter the login and password again to access the settings and you will get to the settings page. Please note that the IP address in the browser will already be different.

Open the settings of the old router

Disconnect your computer from the main router, taking out the cable of the local network and turning off Wi.Fi. Then take the old device and connect it to the LAN Cabel computer. It is not necessary to connect it to the Internet. Turn on the router.

Go to the settings of the old router. To do this, open the browser and enter the address 192 in the search line.168.0.1 or 192.168.One.One.

The menu of the administrator password will appear. If this does not happen, look into the router’s documentation and find out which address by default is set in its settings by the manufacturer.

Enter the login and password. For most routers, this is the same word admin. If it does not fit, again, contact the manufacturer’s instructions. Congratulations, you opened the settings of the router.

New firmware

Everything is done in the same way as on the old firmware, but the menu items can be in other places. Therefore, I write more detailed instructions.

  • Now on the second apparatus of TP-Link, we come in: “additional settings”-“network”-“LAN”. Change the IP address. The last one by 3. The first 3 digits should be like on the main apparatus. “Save”. “restart”;

Convert WiFi router into a WiFi receiver [how to turn WiFi router into a WiFi Access Point]

  • We go to the new address. “additional settings”. “wireless mode”. “additional. Settings”. Turn on the “WDS” mode. We scan the network, find our. Next, prescribe the password and connect to the main receiver.

We make a Wi-Fi receiver from the Router ZYXEL

I decided to start from ZYXEL devices. From the line of routers Zyxel Keenetic. This company has a wide variety of operating modes. And there is a “adapter” mode. On devices with a new version of the firmware NDMS V2, which is blue in appearance.

I will not describe the settings process again in detail, but I just give a link to detailed instructions: Zyxel Keenetic router as a Wi-Fi receiver.

Well, the Wi-Fi network amplifier mode can also be used. In addition, you can not only connect the device to the Internet via cable, but also expand the radius of the main wireless network.