Installing Windows on lenovo from a flash drive

How to install Windows from a USB stick in your Lenovo laptop BIOS?

Read more in this article: how to enter the BIOS of a Lenovo laptop. In the BIOS menu you need to go to the “Boot” section (using the left / right keys). Then you need to select our drive and using F5 and F6 put it to the top of the list. Again, there may be two partitions: EFI and Legacy.

Lenovo G500-series models require the OneKey Recovery key to be pressed with the notebook turned off, and for some models it works FnF2(F12). Find the “Boot menu” and set the boot priority there. To do this, look for “First boot device”, go to it and select “CD\DVD-Rom” from the list that appears.

Frequently Asked Questions

Some ask if you need a special version of Windows for your notebook vs. a PC? No, Windows is the same for everyone, the only important thing is to choose the correct version: XP or Seven/10, depending on the configuration of your notebook or desktop.

To install Windows 7/10, in most cases, it will be enough to know that you have at least two gigabytes of RAM, while the x64 versions need at least 4GB. One more such moment, if your notebook is supplied with a disk with drivers for Windows 7/10, and you, for whatever reason, need to install Windows XP, then before installing it you have to download all the drivers for that OS.

Next, boot from the boot disk with the distribution of the operating system and follow the instructions of the wizard. The procedure will not be different from the installation of an ordinary computer. Also the reinstallation is no different from the installation. Only at the stage of selecting the target drive, you need to format it, t.е. erase old data. For more information see my free video course “How to install Windows 7”

Manual: Installing Windows 7 from a flash drive on a laptop

Interested in installing Windows 7 from a flash drive on a laptop? So in your computer does not have a drive, or it is broken.

What to do in a situation when the CD to boot from the drive is not possible? There is a solution: you can install the operating system from a flash drive.

Before we start describing the process of installing Windows from a Flash card, let’s list all the main steps of the process and then go through them in detail:

  • First: Preparing your laptop to install the operating system (in this case Windows 7)
  • Second: Preparing flash drive
  • Third: Configure UEFI to boot the operating system from a flash card.
  • Fourth: the installation itself.

Note: UEFI is a replacement for the obsolete BIOS.

To begin, you need to move all your files and documents from disc C to disc D. These are usually located in “My Documents” and “Desktop” folders. Some application installation files should be located in the Program Files folder.

Alternatively, you can move all important information to a different flash drive (not the one you are installing from).

First delete or copy all necessary information from the flash card, because the files and folders will be deleted from it automatically in preparation for the installation. Your Flash card must be at least 4 GB in size.

Then you will need the installation files and folders of Windows 7, preferably a disc image in iso format, UltralSO installation utility (you can download it by typing the identical search query). You’re all set? Then let’s get started:

Download, install, and launch the utility. Here is what you will see:

Click on “Trial period”. A new window will open in which you should select “File”. “Open” and point to the image from which the operating system will be installed.

Next, choose “Boot Self-Booting” and click on “Write Disk Image.

Then insert the flash drive into the computer and select “Format”. Once the process is complete, click on “write.

The process will end and you will get a USB key with the Windows 7 operating system on it. Now we can move on to the next step, the installation itself.

You can’t just insert the flash drive into the computer, you need to boot the computer from it when you turn it on. How to do it? Using UEFI. Every computer has one. It contains all the vital settings. One of them is the boot order. That’s where we’re going to stop.

To enter UEFI, press a certain key on your keyboard while booting the system. (This key will vary on many laptops and will be displayed on the screen. That’s usually F2 or Esc.). When you enter you will be presented with a menu you recognize immediately by its blue or gray color.

Many people do not press the Windows logon key in time, and the computer just starts up. If so, you need to reboot and try again.

After logging in, you should enter the menu and find in the settings the boot order of the devices. Here are some example screenshots:

Use the arrows to select the device that boots first. For newbies there is a special help for navigating in UEFI. This is always in a prominent place.

Select USB-HDD. Then exit the UEFI with the “Save and Exit” button. All changed information will be saved. The computer will restart automatically. Now let’s proceed to the next step, the final one.

If you have done everything correctly and the settings in UEFI are correct, you will see “Press any key to boot the CD or DVD”. Of course in English, so a screenshot is attached:

It may happen that on the installation image, in addition to Windows 7, there are other utilities. In this case, you need to select the one that is suitable to start the installation.

The good news is that almost all the operations listed below are done automatically by your computer. And all the settings that you do not like can be changed to your liking after the installation is finished.

A window will open in which you must choose which version of Windows 7 you will install. Click on the one you have the security key for. This is often glued to the bottom of your notebook. The system will request it before completing the installation.

You do not have to enter the key right away. You may do it during one month.

A window with a license will pop up, check the “Agree” box and move on.

Next choose a disk partition, in which “7” will be installed. Press “Disk Setup”. This is usually where beginners have difficulty, so let’s take a closer look at this point.

It happens that in addition to the standard partitions (C, D, E) there are several other partitions on the hard drive. This is due to the fact that when restoring the system was possible to bring the computer to its default settings.

Some find a hidden size, up to 100 megabytes. The operating system will be responsible for its creation. The partition performs the function of the system encryption. The partition has a program that can decrypt it.

But you have to get rid of it. It is necessary to prepare the hard drive for the operation before installing Windows. You can do that with Acronis Disk.

In the window that appears press “Format”. A warning will pop up saying that all the data will be deleted, but it does not matter now since we have a backup copy of all the data. Click “OK”.

Once the formatting is done, go ahead.

Installation will take some time. After that a window will pop up asking the user to enter his and the computer’s names.

If you wish, you can make up a password. In order not to forget it, you will be prompted to think of a hint for it.

Choose a security mode, date and time.

If a network card driver is installed, you must select the type of connection.

So that after installing Windows at startup the laptop is booted from the hard drive, but not from a USB flash drive, you should return the UEFI settings to their original state. This completes the installation of Windows 7 on your notebook!

As you can see, there is nothing complicated about installing an operating system from a flash drive. The main thing is to follow these steps carefully, and you will succeed. Once is enough to memorize the entire process.

Next time you need to install the operating system from a Flash card, you will do it on the “automatic” mode.

Installing Windows 7 from a USB flash drive on a laptop: a guide to action

Enable the BIOS to boot from a USB stick or memory stick.

First, turn off the laptop, then put a flash drive or a memory card in it and turn it on. Now you need to enter BIOS. Usually to do this is to press a certain key at the beginning of the boot. This may be Del, F2, or any other button. It is usually listed on the bottom line of the download window and in your notebook’s manual.

After entering the BIOS you need to set the boot order. Usually these settings are on the Boot tab. To change the boot order you usually use the F5/F6 or F7/F8 buttons. Usually the setup page will tell you what buttons you can use to change the boot sequence. How to change the boot order should also be explained in your notebook manual.

Put your flash drive or memory card at the top of the boot list. USB sticks are usually USB-HDD or something else. Sometimes you will have a USB memory stick model next to the name. The boot order should look something like this:

Boot order in BIOS

Now save your settings and exit the BIOS. To do this, you will need to find a BIOS entry labelled Save and Exit Setup.

After saving the settings, the notebook should reboot. Now you can install the system.

How to Install Windows Using a USB Flash Drive

wikiHow is run like a wiki, which means that many of our articles are written by multiple authors. Volunteer authors worked on editing and improving this article.

Number of views of this article: 17 296.

You have a netbook you want to install Windows on, but you are stuck without a DVD drive? Do you often install Windows and don’t want to damage the installation disks during shipping? It is actually easier than you think to create an installation USB flash drive with Windows. This article will show you how to create a bootable flash drive with Windows Vista, 7 or 8.

Install a free program to create a disk image. There are a number of these free programs available online. You need one that can create ISO files. ImgBurn is one of the most popular free options.

Insert Windows DVD. Open a program to create a disc image. Look for the appropriate options, such as “Copy to Image” or “Create Image”. If necessary, select the DVD as source.

Insert your flash drive. Your flash drive must be at least 4 GB in size to successfully copy an ISO file to it. All of the data on your flash drive will be erased when you copy the installation disc to it, so be sure to back up any important files on the flash drive before proceeding.

Choose USB Device. You have the option to either burn it to DVD or create a bootable USB stick. Select USB Device. Choose your USB flash drive from the list of available drives.

Wait while the program runs. It will format your USB flash drive and copy the ISO file to it. The entire process can take up to 15 minutes. [1] X Source of Information

  • The key to enter BIOS must be pressed when the manufacturer’s logo is on the screen. Usually this is a very short period of time and if you miss it, reboot and try again.
  • The key depends on your computer, but will definitely be displayed. Typical keys for entering the BIOS are: F2, F10, and Del.

Navigate to the boot menu. The menus of the different versions of the BIOS differ from each other, but generally all have a boot order (although this may be worded slightly differently). The boot order displays a list of devices from which the operating system is booted. Usually, computers are set to boot automatically from the hard drive.

  • Insert your installation disk/flash drive into the floppy drive/USB port. Configure the BIOS settings correctly
  • Wait for the notebook to start after rebooting. Then the installation process will start immediately.
  • Study the instructions that pop up on your screen
  • The next step is to format it.

Open Advanced BIOS Features with the down arrow and press Enter. Press Enter on the highlighted 1st Boot Device. A list of devices from which you can enable booting from USB flash drive in the bios appears. To boot from the flash drive you need to select with the up and down arrows item USB-HDD or USB-Flash, and then press Enter.

First we have to enter the BIOS itself. Press the power button, as soon as the notebook display lights up, or rather matrix backlight turns on, immediately press the F12 key (if I’m not mistaken, it is the key to enter BIOS).

Installing Windows 7 on Lenovo G50-30, G40-30 and other laptops of this series

When installing any version of Windows (xp, 7, or 8) from any media with a flash drive or DVD-ROM on your laptop Lenovo ideapad G50-30 or Lenovo ideapad G40-30 error 0x0000A5:

The same error will occur when trying to load various test utilities. MHDD, MEMTest, etc. п. No need to panic, most likely there is nothing wrong with your laptop. the problem lies in the BIOS version and its settings. If you have a model with preinstalled Windows 8. you can directly from it to update the BIOS and then put Windows 7. But most packages come with preinstalled FreeDOS, in this case you can not update the BIOS and have to configure the BIOS.

To enter BIOS on Lenovo G50-30 and G40-30 use the combination FNF2 when you turn on the laptop or the Novo Button. You will be shown a window with the notebook model, BIOS version and other information:

Navigate through the menu with the arrow keys, go to the tab Boot and set the settings as shown in this picture: Boot mode = Legacy support Boot Priority = Legacy First, leave the rest as is

Go to the tab Exit and choose in order in the first item put the desired OS Windows 7, Windows 8 or Other if you want to put another operating system, then select the second item, press Enter and agree to load the default settings. Remember the 3rd point, don’t touch it for now.

Go to the tab Configuration and in the USB Mode. select USB 2.0, this is needed for the duration of the installation of Windows from USB flash drive, after installing it you have to return the settings back to USB 3.0 and then check that all the settings that we have changed have the right values, go back to the Exit tab and perform the 3rd item. After that, if all the settings are correct, the installation of Windows will go without any problems. A little nuance, if you have Windows 8 installed and want to install Windows 7, you probably need to convert the partitioning of the disk from GPT to MBR, to do this do the following:

Installing Windows on lenovo from a flash drive

I want to tell you about, as it seems to me, not exactly the right policy of Lenovo Corporation.

A friend of mine asked me to install Win 7 on my just-bought Lenovo B50-30 laptop. The model is quite budget and had on board 2 GB of RAM, so the Win 8 installation is not even a question. I inserted a multi-boot flash drive and started looking for how to load the quick boot menu. It turns out that in this model you can do it in two ways. The first way is to press the FnF12 shortcut when powering on (why not just F12). The second way is by pressing the small button on the right sidebar (in earlier models it was near the power key, which was much more convenient). I chose to boot from USB flash drive, the installation began and after a few seconds the laptop went into a blue screen. Trying to do this a few more times, changing the flash drive to a multiboot drive failed. I decided to install the system from a disk, but got the same result.

After a bit of cursing I started to look for a solution on the Internet. After trying a couple of variants found in the search engine (I even offered the option to upgrade the bios, which for the average user is not good at all), yet one of them turned out to be working. This option helped me:

In the last BIOS menu in the last line of the OS optimized Default line change the value from Win8 64 bit to Other OS. 2. Make sure to do Load Default Setting. 3. Save changes in this order. 4. Install Win 7 x64/x86 without BSOD.

After that the installation went as usual and completed successfully. But this was not the end of the story. After installing Win7 x32 I started installing drivers as usually done using the driverpack. Could not find drivers for USB 3.0 and graphics cards. I didn’t give up and decided to download it from the Free Software. Notebook vendor’s website. There I was disappointed, because the drivers for this model were not available on the. After that the searches of drivers by ID and various, intended for this programs began. Ended up in failure. Perhaps if it was my laptop I would have fiddled a bit more, but since I had already spent the extra 2 hours, I decided to accept it and install Win 8. The OS got up without problems and all drivers were found. But in my opinion, it is not quite right from the manufacturer’s side to force the user to use the OS that the manufacturer wants, not the one that the user wants. And in terms of speed, 2gb of RAM isn’t quite enough for normal Win 8 activities. I’m a little disappointed in Lenovo. “You’re going the wrong way comrades.”.