Before you turn to the instructions, you need to understand what caused the iPhone not to turn on and the apple is lit on a black screen. The following reasons are listed:
Sometimes the battery is low and the phone is completely discharged, so you see an apple. Try plugging in your charger and after waiting about 20 minutes try turning your iPhone back on.
Your phone freezes when you turn it on, the “Power” button may be broken. Happens when you disassemble the iPhone.
Doesn’t boot beyond apple device. malfunction in the device’s power supply. This often happens with phones during surges in the network when charging.
The charging controller broke, there were power outages.
Problems with the power circuit of the device. The device was charging during the power surge.
Problems with the motherboard, and the phone itself may even boot up sometimes and even work for a while. The glowing apple on the iPhone screen will appear more and more often, until it does not start up normally at all.
iPhone: apple lights up, but does not turn on. what to do in this case?
The problem when the iPhone does not turn on, the apple lights up and turns off. There are not many reasons for this. The main ones are:
- Low battery;
- Failure of the AC adapter, which cannot charge the smartphone;
- Software error;
- Breakage of internal components of the device.
Most of these problems are quite possible to solve even without leaving home, the main thing is to act according to a certain algorithm, which is very easy to remember.
The most common and trivial reason is the lack of power to boot. It is enough just to put the smartphone on charging, after about 20 minutes try to turn on the phone again. If nothing happens, check the power adapter, maybe the charger is not working.
Firmware failure. Often a black apple on a white screen hangs during the installation of updates. In this case, if the iPhone is connected to a computer, you must disconnect it. Then press and hold the Home button and the wake-up button at the same time for 5. 7 seconds on models before version 6.
In iPhone 7 to reboot, you must simultaneously press and hold the wake button and the volume key, press on the side of the sound reduction.
On iPhone 8 and all newer versions, the wake-up button and volume button are centered. After this the smartphone should boot normally.
If this procedure does not help, proceeds to recovery. To do this, you need to connect the iPhone to your computer. If using Windows MacOS before Catalina restore via iTunes, in the latest version of MacOS interaction between the smartphone and computer is through the Finder. If you are not sure about the automatic backup mode it is better to apply to AppleLab service engineers for help.
If all these manipulations do not help, most likely there is a problem with the internal components of the device. You can determine the exact reason of the problem only after diagnostics in the service center. AppleLab provides free diagnostics and consultation by phone. So if your iPhone screen is flashing and nothing happens, call us immediately, we can help solve any problem.
iPhone doesn’t turn on and the apple is lit, what to do? Here are 4 solutions!
Freezing on the Apple logo on the screen is one of the most common problems faced by iPhone users. Especially those who have recently purchased a device of this brand, and do not know about all its features they can easily face the fact that the iPhone hangs on the Apple logo after hacking or recovery. Your precious device will completely turn into a “brick” and cause you a lot of problems and worries: you will not be able to call someone, write or take a picture.
Iphone 7, 7, 8, 8, x black screen unresponsive, dead, won’t power on, quick and easy.
There are four methods to fix iPhone freeze on screen with Apple logo. They are applicable not only for iPhone, but also for iPad, iPod touch after updating to the latest version of iOS, hacking, water damage and much more.
Forced reboot iPhone Fix iPhone hangs on Apple logo without data loss (using special software) Restore iPhone to factory settings using iTunes DFU mode (restore a hung iPhone)
There are many reasons for an iPhone to get stuck on the Apple logo. It can happen during the upgrade process, data transfer or hacking, or your iPhone can get stuck on the Apple logo after physical damage. Identifying the reasons why your iPhone is stuck on the logo is important, so try to understand why it happened. The problems can be divided into two categories: software and hardware.
⦁ Software problems often cause your iPhone to hang on the Apple logo
Software problems are the most common reasons why your iPhone hangs on the Apple logo. Something may have gone wrong during an iOS update, data transfer, hack, or iPhone recovery. And some users using an older version of iOS may also encounter this problem.
⦁ Hardware problems also cause the iPhone to hang on the Apple logo
Hardware problems are mainly caused by physical damage. For example, you’ve accidentally dropped your phone, and that drop can cause internal damage, causing the iPhone to freeze on the Apple logo. Immersion in water can also cause damage to the hardware, resulting in a black Apple logo. So you need to be careful when you shower, swim, or even just go to the bathroom. it’s best not to take your iPhone with you.
So, the iPhone is stuck with the Apple logo (the device does not turn on and the apple is lit). What to do next?
Forcibly restart your iPhone
Forcing a restart won’t cause data loss, and it can help get an iPhone stuck with the Apple logo back up and running. However, be sure to try this method first. Here’s what you need to do to reboot:
iPhone X, iPhone XS, iPhone XR, iPhone 11 or iPhone 12, iPhone 8 or iPhone SE (2nd generation): press and release two buttons: volume up and volume down. Now, hold down the side button and release it until you see the Apple logo. After that, check your iPhone and see if it starts up.
iPhone 7: Press and hold down the volume down button and the sleep/wake button at the same time. When the Apple logo appears, release both buttons.
iPhone 6s or iPhone SE (1st generation): Press and hold the sleep/wake button and home button simultaneously. When the Apple logo appears, release both buttons.
Fix iPhone freeze on Apple logo without data loss (via software)
When an iPhone won’t turn on and the apple is lit on the screen, most people don’t even know that it can be repaired themselves. That’s why we highly recommend Tenorshare ReiBoot, the best iPhone software repair program. This iOS system recovery tool offers you the most effective way to fix iOS freeze problems such as white apple screen, black screen of death, recovery mode, no screen response, appearance of “support.Apple.com/iPhone/restore” much more. Download this iOS fix tool for free to see what it can do.
⦁ Download and install Tenorshare ReiBoot on your computer and connect your hung iPhone to your computer using a USB cable. Click “Start”.
⦁ ReiBoot will display the appropriate firmware package, which you can download. Download the IPSW file and follow the instructions to restore iOS on your device.
⦁ After restoring the system, the Apple logo will appear on your iPhone, and all the data on your phone will be restored.
Restore iPhone to factory settings using iTunes
This is another easy way to fix your iPhone hanging on the Apple logo problem. In the process, all data on your device will be deleted (so back it up before restoring it).
Run iTunes on your computer, connect your iPhone to your computer with the cable, click on the iPhone icon and select “Browse”.
Select “Restore iPhone” to restore the iPhone to factory settings.
DFU mode: Restore a frozen iPhone
DFU means updating the default firmware, it’s also one easy way to fix the problem of the Apple logo getting stuck on your iPhone. Just follow the instructions below.
Keep in mind that DFU mode clears all data on your device, so it’s recommended to back up your iPhone beforehand (for example, with Tenorshare iCareFone).
Run the newest version of iTunes on your computer and connect your iPhone to it.
Press Power and Volume Down for 10 seconds. Then press the power button while holding down the volume down button for longer than 5 seconds.
The iPhone screen will turn black and you’ll see an iTunes pop-up on your computer notifying you that your iPhone has entered DFU mode. This will completely reset your iPhone’s firmware to factory default.
This method works in most cases, but if you want to fix an iPhone stuck with a white Apple logo without recovery or data loss, ReiBoot would be the best choice.
These are the most common and effective methods of fixing and repairing an iPhone stuck on the screen with the Apple logo. Choose the one that’s right for your particular case, and get your device working properly.
First of all, it’s important to figure out the reason why your smartphone refuses to turn on. Here’s a list of the most common causes:
- Your smartphone battery is low. In such a situation, the iPhone turns on before the apple, and then shuts down.
- iOS glitches. If the screen lights up but the iPhone doesn’t work, it can be fixed with a hard reset or factory reset.
- Hardware failures caused by various mechanical impacts, moisture or other negative factors.
What to do if iPhone does not turn on because of mechanical impact, or the screen permanently dims right after turning on?It is worth to take your smartphone to the service center. Hardware problems can be very different:
iPhone 7 / 7 Plus: How to Fix Black Screen/ Wont Turn On/ Blank Display
- Moisture inside the case.
- Short circuit with damaged components. It is almost impossible to find the place of damage on your own.
- The power button does not work. To detect this problem is not difficult. Simply plug your iPhone into the charger and if the power button light comes on, then the power button is broken.
If you decide to repair your iPhone yourself, you must remember that in this case you will lose your warranty. But more importantly, it is possible to damage other elements, and then the repair of your smartphone will be much more expensive.
iPhone doesn’t turn on, apple is lit. Here is what to do
Despite the fact that Apple technology is most reliable and stable, as they say, once a year and the stick shoots. And it can “shoot” anywhere. It happened to my iPad that suddenly shut down and never came back on. It’s just stuck on the apple logo. I rebooted it several times, tried to update and even reset it to factory settings through iTunes. Neither of these things work. Your iPad still won’t boot up past the apple. So, you had to go to more drastic measures.
It also happens that your iPhone can freeze on the apple for no apparent reason
If all else fails
None of the above methods helped? This means that your iPhone has a physical problem and you need to contact the service center.
Why won’t the iPhone turn on??
A dead battery is the most common reason for my iPhone to stop working. If you’ve noticed before that your smartphone rapidly ran out of power, shut down at 10-30% of charge, shut down in the cold, or had any other similar anomalies, then the problem is definitely with the battery.
FIX IPHONE NOT TURNING ON/Stuck At Recovery Mode/Apple Logo/ iOS 13 and below. iPhone XR/XS/X/8/7/6
Replacement will help. In the authorized Apple service centers in Russia is more expensive. 3000-7000 thousand.
A broken power supply controller is another very common cause of iPhone malfunction. Symptoms before the smartphone fails are similar to battery failure. accidental disconnection of the device, overheating.
Replacement is relatively inexpensive. To change a power controller or another chip related to the charging process, it costs around 2000.
Failure of other components. iPhone may not turn on due to failure of dozens of different components, up to the motherboard. This happens most often after you drop your smartphone. You can determine what is broken only during diagnostics.
Repair can ruin. If the iPhone did not overheat before it broke, it is better to immediately begin to pray that the motherboard is intact. Its replacement, especially on newer iPhones, will cost a pretty penny.
Before you go to the service center, we recommend contacting official Apple support. The company’s specialists will be happy to help you with advice.
The iPhone does not turn on and the apple is lit what to do?!
Tablets and smartphones from Apple have long gained a reputation as a fairly reliable devices. And the operating system iOS did not give much reason to complain. Nevertheless, sometimes problems occur electronics, no matter how you look at it, is a capricious thing. One of the most common phenomena iPhone doesn’t turn on and the apple is lit on the screen. At this point, the phone freezes and you can not turn it off in the usual way. The probable causes of this trouble are quite a few. Let’s try to understand them and if possible, let’s try to fix them ourselves.
Very common, but one of the most common reasons. The user is sure that the phone battery is charged, but it is almost completely discharged. Try plugging in your charger and after waiting about 20 minutes, try turning your iPhone back on. By the way, this is also possible if the charger is defective. The user thinks that the device is charged, but it is just completely dead. Try charging from a computer with a USB cable.
If you have recently installed any application, dug in the settings or tried to make a jailbreak, then with a high degree of probability we can say that this is what caused the failure and the appearance of the glowing apple. Very often helps a so-called Hard Reset your phone with Home and Power button, which you should press and hold for 8. 10 seconds. In more than half of all such cases the iPhone successfully boots up and works. Do not forget to disconnect it from your computer or charger. It did not help? Then you should try to reflash the device. To do this, you need to run the iTunes program on your computer, then connect the iPhone to the computer with a USB cable. Then we turn it off holding Home and Power buttons. Hold it until the screen goes out, then release the Power button, but do not release Home. This puts your iPhone in the DFU mode. The screen will be black, but the computer should display a message that the device is in recovery mode. Release the Home button. Press the Restore button in iTunes, it will download and install the new firmware.
After this procedure, you will get a blank device without settings and additional programs, and the burning apple on the iPhone should disappear.
unfortunately, the reason why your iPhone does not turn on and the apple is always lit is because of hardware problems. And here already flash or not flash, and it will not work all the same. What can cause it?
Failure of the Power button Very often this unpleasantness comes to those, who have removed the casing of the iPhone. And it seems that the power button is not so flimsy, but nevertheless it can be broken.
Problems with the power circuit of the device Several times we brought such phones after a thunderstorm. The device was lying on the charger during a power surge.
The charging controller is broken Exactly like the previous failure, usually associated with problems with power supply surges or sagging voltage in the network.
The battery is completely dead This problem often occurs when you drop your iPhone and the battery is damaged internally. The battery may also die due to improper use (charging and discharging).
Failed Flash-memory And it can be failed the data memory chip NAND Flash, and Nor Flash memory of the GSM-module, which stores the operator’s network parameters.
Problems with the motherboard At the same time the phone itself can sometimes even boot up and even work for a while. The glowing apple will appear on your iPhone screen more and more often, until it does not start up correctly at all.
Unfortunately, this kind of failure with their own hands to fix it will only be able to those who are friendly with the soldering iron and multimeter, the rest of the users have only to take it to the service center for repair.
Diagnostics and fixing problems
The problem may occur more than once in this case it does not hurt to find out the cause. You can use special diagnostic software. For example, Tenorshare ReiBoot is a program that helps diagnose errors and get your iPhone back up and running. You can do it with just a click of a button.
Download the software from the website.
Install the software on your PC following the instructions of the setup wizard.
On the welcome screen find the item “Enter recovery mode”.
Then you need to press “Start”, the program will update the firmware of the smartphone. The ReiBoot developers claim that the iPhone data will not be affected. detailed instructions for use can be found on the official website.