Set up Wi-Fi router as an access point. Change of standard administrator password

Good wireless Internet can only be provided using a high.quality router or router. Mobile access cannot boast of such an impressive speed and stability of the connection. Only Wi-Fi connection remains. To ensure it, a Wi-Fi network access point is used-this is a special device for organizing wireless access to the service provider network. Is a transparent bridge between the wired network and the wireless. For most simple Wi-Fi users, the point and router are the same. However, it is not. If you delve into the essence, then you can determine the differences.

Using a global network has become very simple. The market is rich in a huge number of operators and providers who provide access to the network. If some time ago, only the elected Internet access had access. For example, by purchasing a very expensive computer and connecting access through a modem at a speed of 56 k, from which it was necessary to call on an ever.busy phone number. Today everyone can afford the Internet. He became not a luxury, but a banal necessity: for work, communication, obtaining information, games and other things.

The average user has access from a personal computer, laptop, phone and other devices. However, to enter the network, each user wants flexibility so that there are no wires and additional equipment. It is in such cases that you have to deal with wireless assistants.

wi-fi, router, access, point, change, standard

Most users do not distinguish wireless devices among themselves and call them routers, routers, access points and anything else. You can often hear how customers complain to their own Wi-Fi point, although in fact it turns out to be another device that does not even support the Fast Ethernet standard.

Important! Wireless Access Point or Wi-Fi access point is a special device for the wireless connection to the operator network.

A router or router is a device that organizes access without a wire or with it. It can route traffic between different network segments. A simple home router is just a device that can organize a network environment independent of the operator. In this network, it is possible to register any home devices in various quantities. The indicated network is an absolutely autonomous and independent of the service provider. Only the user can decide on the connection of new devices, limit or allow them access.

The provider defines the end point simply as a router of the consumer of services.

Access point or Wi-Fi Hotspot is that it has no signs of routing. Its principle of operation is to switch packages and transfer them to the wireless part of the network from the wired. It cannot function regardless of the connection supplier. The decision on the registration of new devices and the limitation of their connection is made by the provider, and not personally by the user.

Need

According to the principle of functioning, TD is more like a standard extension cord of an electric network. However, here, instead of electric current, there is a connection with the global network through the air. Wi-Fi AP (TD) are divided into two types that depend on their application:

  • Option for industrial use. The presented look has very strong relayers. They are used to transmit the signal through a Wi-Fi network over long distances and is designed for a large number of subscribers.
  • For home use. Such devices are used in the house, apartment, office. The device is directly connected to the global network and transmits a signal to all users who have the right to access the wireless channel.

note! The main difference between the specified types only in the power of the transmitted signal.

Certain models of devices have a built.in repiter mode. He applies wireless communication both for the provision of remote Internet access, and in order to distribute the connection to subscribers. The disadvantage is low in the process of use for the final connected device.

wi-fi, router, access, point, change, standard

Almost all TD have a single principle of work. With each new user connected, the general channel is divided evenly. The wired device integration has only one LAN output and food wire.

Setting up a virtual wireless integration

The very first step will create a new security profile, as to make an open guest network. This is a very bad idea, and for organizations there is also a violation of the law requiring mandatory identification of users. To do this, we will open wireless. Security Profiles and add a new profile. The settings are simple: Mode. Dynamic Keys, Authentication Types. WPA PSK2, WPA2 Pre-SHARED KEY. Password access to the network, from 8 characters, NAME. arbitrary name of the profile, in our case guest.

The terminal team, as a password, we set 987654321:

Now let’s go to Wireless. Wi-Fi InterFaces and add a new virtual integer by clicking on the button with a plus and choosing in the drop-down menu Virtual.

In the window that opens, we indicate the mode of operation of the Mode intend. AP Bridge, select the main physical radio interfac. Wlan1, we indicate the desired SSID and select the security profile in Security Profiles created for the guest network previously created for the guest network. We also remove the Default Forward flag that excludes the communication of guest devices among themselves. We leave the remaining parameters by default.

There are larger settings in the terminal, you will also need to specify the MAC address that should be taken from the physical wireless intensity.

If you have a two.band access point and you want to create guest networks in each of them, then create another virtual wireless integrate and indicate as Master Interface the second wireless adapter. The operating frequency, channel width, power and other settings virtual adapter inherits from the physical intese. T.e. The guest network will work on the same channel and with the same parameters as the main.

Then we move to the Bridge and create a new network bridge, in the ARP parameter we indicate the Reply-only, which will force the router to answer the channel level only to well-known devices, which will significantly limit amateur performances in the guest network, so guests will only be able to work with the settings received from the router, yourself to set up network parameters will not work.

The command line is the same action:

Then we add virtual wireless intenses created by us, using a graphic intense in the Bridge section. Ports or in the console:

After that, we will appoint an IP address for him, for the guest network you should choose a separate range of addresses that does not intersect with your networks, in our example it will be 192.168.134.0/24, the address of the router in this case will be 192.168.134.one. Open the IP. Addresses and add a new address, it should be indicated in 192 format.168.134.1/24 (which corresponds to mask 255.255.255.0), in the Interface Field, select the integration of the network bridge created in the previous step, we have it Bridge2.

Or complete in the terminal:

If you need several guest networks with a different level of access, then create the right number of virtual network inteys and bridges (one for each network), as well as assign each network your own address of the address.

Setting up basic network services: DHCP, DNS, NAT

To configure the DHCP server, we will use the master, for this we will go to IP. DHCP Server. DHCP and click the DHCP Setup button, in the opened mastere, we choose the integer. Bridge2 and consistently answer a number of questions, asking a network, a pool of addresses, a gateway address, etc.D.

But when specifying a DNS server, we should think, we can indicate the speed of the router and use the service existing on it, but in some cases it may be undesirable, for example, you have records for internal services, and you do not want their leakage to the external net. Or you need to additionally filter the contents given to guest users. In this case, as a DNS server, you can indicate the address of any public service that is suitable for your requirements.

On the other hand, your own DNS server allows you to independently block some resources, you can read in more detail about it here.

After completing the work of the master, open the created entry in IP. DHCP Server. DHCP and set the Add Arp for Leases flag, now the server will dynamically add customer MAC addresses who have rented an ARP table so that they can work in the guest network. At the end of the lease, such a record will be deleted and even if the client reconfigured his device to a static address after a while, he will lose access to the network. In this regard, pay attention to the LEASE Time parameter, which sets the time lease time, by default it is 10 minutes, a very reasonable interval, but you can increase it (if it is a network for personal devices of employees) or reduce the speed up of the address of addresses.

To configure the DHCP server in the terminal, execute:

In order for customers of the guest network to go on the Internet, you should configure NAT, go to IP. Firewall. NAT and create a new rule: chain. SRCNAT, SRC. Address. 192.168.134.0/24. The range of the guest network, out. Interface. External Inte Weep, through which the Internet is made, in our case Ether5. On the Action bookmark, we put the action of Masquarade.

Or in the terminal:

Now is the time to make a short pause and try to connect to our guest Wi-Fi network, make sure that the device receives the address and it has Internet access.

If you have not been mistaken anywhere. Everything should work.

Notes of IT specialist

Wi-Fi in Mikrotik routers is quite an ambiguous topic, on the one hand the number of publications devoted to it is quite large, but on the other hand, most of them are a simple listing of all the settings present in the router with a brief description, without explanations about their appointment, need, or,,,,,,,,,,,,,, Keeping On the contrary, unnecessary. Therefore, in our article we will focus on practical application and options that you really may need in everyday activity. And also give the necessary theoretical minimum to understand the meaning of individual settings.

You can learn how to configure Mikrotik from scratch or systematize existing knowledge in an in.depth course in administering Mikrotik. The author of the course, the certified Mikrotik coach Dmitry Skoronov personally checks laboratory work and controls the progress of each of his students. Three times more information than in the vendor program of MTCNA, more than 20 hours of practice and access.

We will immediately make a brief retreat so that then no one has misunderstanding and disappointment. In part of Wi-Fi, most of the Mikrotik routers are seriously inferior even by inexpensive household routers, this is due to an obsolete hardware platform that does not support many modern standards and technologies. Therefore, if you need a really productive Wi-Fi network, you should use the equipment specially designed for this for this. access points, leaving the router his main tasks.

It should also be understood that it is almost unrealistic to achieve productive work from Wi-Fi networks in conditions of dense urban development, wireless networks, especially in the 2.4 GHz range are very strongly overloaded, and a large number of transmitters, often twisted at maximum power, make the etheric situation extremely unfavorable. In addition, wireless communication. This is a separated environment, if each consumer receives its own channel at least 100 Mbit/s width through the cable, then even the clients working in ideal external conditions will share the only 150 Mbps/s wireless channel.

Therefore, connect by Wi-Fi demanding to the throughput of the device network, especially multimedia. This is not the best idea. Wherever possible, you should use a cable connection. As for most models of Mikrotik routers, they are well suitable for organizing wireless networks designed for a small load in offices, compensating for all the shortcomings of the obsolete wireless platform with wide Routeros capabilities, which make it possible to very flexibly configure the parameters of the wireless network and the rules for accessing it.

All Routeros wireless settings are located in the Wireless section, opening which we will see a list of wireless intenses, depending on the model of the router there will be one (2.4 GHz) or two (2.4 GHz 5 GHz). Most settings for both ranges are the same, so we will consider them in relation to the range of 2.4 GHz, making the necessary digressions where the parameters specific for the range 5 GHz appear.

To configure, we will open the necessary integer and immediately switch to the Wireless bookmark, on which we turn on the extended mode. Advanced Mode.

Now let’s move on to the consideration of the first settings unit, which is responsible for the operating mode of the access point and the frequency range used.

Mode option is responsible for the operating mode of the wireless device. In our case, this is AP Bridge. The mode of the transparent access point, we will consider no other regimes within this article.

Band. Wireless network work standards. For a range of 2.4 GHz are available B, G and N, for 5 GHz. A, N and AC. Standards A and B have not been found for a long time, so N and AC are relevant, there may also be a device with adapters of the standard G. Therefore, for the range of 2.4 GHz, the best choice will be 2GHZ-OLY-N, for 5 GHz. 5GHZ-ONLY-AC or 5GHZ-N/AC, depending on the Park of User Devices. As for the devices of the standard G, if there is a need to use them, then the creation of a separate wireless network for them will be a more correct choice.

Frequency. channel frequency. You can, of course, put in Auto and forget, but in modern conditions this is not the best solution. Let’s look at the example of the etheric situation in an apartment building. Two most powerful networks on the first channel do not take into account, these are our two own points: home and test.

wi-fi, router, access, point, change, standard

As you can see, everything is not very good, if not differently. The edges of the range are more or less free, while choosing the beginning is more preferable, both in the air of the environment and for compatibility, many devices, for example, Apple products do not work above the 11th channel.

Well, let’s not forget about the classics for 2.4 GHz: 1. 6. 11 (frequency 2412. 2437. 2432), it is precisely these non.overturning channels to choose for work. And even if we don’t get better from this, then we will at least not do it worse than everyone else, although in that chaos what is happening in apartment buildings and office centers is a rather weak argument.

Real trouble of the range of 2.4 GHz. wide 40 mHz channels, which use two adjacent 20 MHz of the canal, and since the channels are shifted relative to each other by 5 MHz, it turns out a shift for 4 channels, t.e. 15 or 610. At the same time, the main one is one 20 MHz channel, in which all service information is transmitted, and an additional 20 MHz channel is used only when the main bandwidth begins to lack. And if your main subscribers can only work with a 20 MHz channel (most mobile devices), but your point works on 40 MHz, then you will only interfere with your neighbors, without any benefit for yourself.

How to configure the ASUS router mode?

In different models, setting the router mode occurs in different ways. We will need to connect to some existing Weifia, which is distributed to some other router, and spread it already in our apartment. I show with the example of ASUS RT-N10U B in the new firmware.

We go to the admin panel (https: // 192.168.one.1), the “Administration” item, the tab “mode of operation” (red), or immediately click on the “wireless router” at the very top of the settings page (green).

Currently, the default “wireless router” has been activated by default. You will find its settings in this article, and we will put the flag in the second account. the repeater mode mode. And click the “Save” button.

A page will open on which all wireless networks will be displayed in the radius of the router. Choose from them the one to which we need to connect and introduce an access key if it is parolen.

Click to connect. After connecting with a third.party router, you can make another interesting settings: either use data to access the existing network that we lengthen. Or set our own. then we connect to ours with the same data (SSID and password), and to the second one in which the Internet cable is directly inserted and the signal of which we lengthen with others.

Further is the technique. we are waiting for all these settings to be applied and you will turn off the network. After that, in the list of available wireless connections, the new one that has just created will appear. We connect to it. and go, through the open spaces of Runet!

ASUS router in access point

The mode of access point A to Asus is that it is connected by a cable to another router or modem, which in turn is connected to the provider and already transmits further the Wi-Fi signal. It is convenient to use it if you have the Internet through the ADSL modem, but the router itself does not have such a built.in possibility. Or if your router is not equipped with a wireless module and cannot distribute a Wi-Fi signal. I think it makes no sense to disassemble it, since everything is described in detail in the article about the modem in the router mode, the link to which I already gave above.

ASUS router in bridge mode, or client

Client is the one who gets something. This mode is called this because with it the router works in the opposite direction-it does not broadcast a wireless signal from a connected cable, but on the contrary, it receives via Wi-Fi Internet from a different access point and spreads it to other devices using a cable. This work procedure is available only in some models.

The most striking example of the apparatus working in this vein is Wi-Fi Adapter. And from routers, asus EA-N66 has this ability.

This mode is called in this model “Wireless network adapter”.

This type also allows you to combine two autonomous networks using a wireless “bridge”. When creating such a connection, it is necessary that both routers have this mode (Bridge). Or you can make sure that one device is activated as a “access point”, translating a signal, and another as a “client” that accepts it and distributing it to the cables to computers of his network. From the line of Asus, with which I am a fan, for organizing such a bridge, a modern model RT-N13U is suitable.

In this note, I listed all the main modes of the Wi-Fi router and listed their most common names. Read more about the setting of each of them I describe in separate articles on the blog. If you came across any other and you do not know how they work, then write in the Комментарии и мнения владельцев, we will understand together.

Infrastructure mode with several AP

This parameter is very common in a corporate environment where it is necessary to provide Wi-Fi access in vast territories or where there are a large number of devices. The key, therefore, is the need to have a cable infrastructure, because everything should be connected to the wired network, where the router is located, which provides access to the Internet.

This mode of operation is completely compatible, that is, it works using AP different manufacturers. It is important that all AP uses the same Wi-Fi standard and the same parameters (SSID, Safety type and key).

In the photo on the left, you can see AP installed on the wall to cover a certain zone. In the photo on the right, you can see a communication cabinet that contains a switch in which all AP and Internet access router are connected.

In the next figure, you can see the location of the three ophers to cover the required area.

The following drawings shows the screens of the configuration of three PLO from different manufacturers, which are part of the same Wi-Fi network for calling wifi_Prueba.

When the number AP, which make up wireless networks, some manufacturers provide solutions, such as software as equipment for effective control and message exchange systems on all devices. The disadvantage in this case is that everything should be from one manufacturer to ensure a solution to control.

Access point from the Router Zyxel Keenetic

If I am not mistaken, then only the Keenetis Lite III model has a mechanical switch of the operating mode on the case. In all other cases, we go into the settings of our Zyxel Keenetic. I immediately advise you to configure the Wi-Fi network (set the name of the network and password, if necessary). so as not to deal with the entrance to the AP settings.

To activate the access point of access to ZYXEL, go to the “System” tab, and open the “mode” tab on top. Highlight the point “Access point-expansion of the Wi-Fi zone with the connection via Ethernet”, and click the “Apply” button.

Allow the router will reboot. After that, you can connect it with another router, and it will already work in “Access Point” mode.

To go to its settings, you can first go into the settings of the main router (modem), go to the customer list, and see the IP address of our ZYXEL there. And already go to the web-integer on it. And you can just dump the settings, and the router will work as usual “Internet center”.

TP-Link router as a Wi-Fi access point

If you have a device from TP-LINK, you will need to manually change several parameters. Since the operating mode switch is not there. Now step by step will show what and how to do. I will show on the example of the router TP-Link TL-WR740N.

1 To get started, we go into the settings of the TP-Link router, which we want to configure in a wireless access mode. And change the IP address of the router. To do this, open the “Network”. “Lan” tab. We need to set the IP address, the same as the main router (you can see on the device itself). only with another number at the end. For example: if the IP address of the main modem (router) 192.168.one.1, then in the TP-Link settings you need to set 192.168.one.2, and save the settings. The router will be rebooted.

How to Login to Linksys WRT54GL and Change Default Router Password #webdevpro

Go to the settings again, but already at the new address. In my case, this is 192.168.one.2.

2 Wi-Fi Network Settings. If necessary, then on the Wireless tab, set the Wi-Fi settings for our access point. Indicate the name of the network and password.

3 last step. Disconnect the DHCP server. To do this, go to the “DHCP” tab. Put the switch near “Disable” (disconnect) and save the settings.

And reboot the router. You can through the control panel. The System Tools tab. “Reboot”, button “Reboot”.

We connect it to the main router (LAN. LAN). and we get a wi-fi access point.

Setting Access Point on Netis routers

On my Netis router, I just just changed the IP address, turned off DHCP, and everything worked. Go to the settings at Netis.CC.

Open the Network tab. “LAN”. Change the IP address. If the main router, or modem 192.168.one.1, then we write 192.168.one.2. That only the last figure would differ. There we turn off the DHCP server. And keep the settings.

If necessary, then we go back to the settings (already at the new address that we set). and on the “Wireless mode” tab we set the Wi-Fi settings.

We connect our Netis access point with the main device with a network cable (LAN. LAN). And everything is ready.

Where to put it? Evaluate the room before installing an access point

It is very important before installing an access point to understand the data transfer environment and where there are potential interference. Sloks can be everything that works in the same or close frequency range:

  • microwave;
  • Wi-Fi routers of neighbors;
  • Bluetooth device;
  • USB 3.0 can also be source of interference in the range 2.4 GHz;
  • household appliances with built.in wireless intenses;
  • and t.D.

We advise you to place a Wi-Fi router as far as possible from sources of potential interference. It will also be useful to look into the radio spectrum and evaluate how many other devices are working around you and find out the level of their signal. For this you do not need to have supernatural abilities. To measure the signal level from the access point, albeit less accurately, without specialized equipment. For example, using a smartphone and one of the mobile applications for scanning Wi-Fi networks, which we once made a review.

  • https: // apkpure.COM/ru/wi-fi-scanner-net-discovery/com.NUTSABOUTNETS.Wifiexplorer
  • https: // apkpure.com/ru/wi-fi-welden/com.XTI.Wifiwarden
  • https: // apkpure.COM/ru/wi-fi-monitor-ANALYZER-OF-WI-FI-NETWORKS/COM.Signalmonitoring.Wifimonitoring

Of course, the above solutions will not replace professional equipment, but in any case will make it possible to approximately evaluate the levels of signals around you. Set your router at the point where the signal level from neighboring devices does not exceed.60 DBM. Do not forget about natural obstacles in the form of walls. Depending on the material used and its thickness, the coating area will also change fundamentally. The power in the range of 5 GHz is especially lost, when, having passed through one wall, the communication quality will no longer allow you to work comfortably with Real-Time services.

With professional design, radio planning is calculated, for this, even specialized in. However, lovers, we can recommend simply not placing access points close to the walls, especially reinforced concrete. The most optimal location is the middle of the room, away from other household devices.

TP-Link

How to give the Internet from a mobile device

The access point can be a phone or tablet. You can do this with standard android OS or using special programs. It is worth noting that only mobile Internet will be distributed to connect GSM, 2G, 3G, 4G. You cannot configure the distribution from Wi-Fi.

Setting up android devices as a router

Starting with Android 2.3, the operating system allows you to be a connection translator for other phones, tablets and laptops with a Wi-Fi module. Before creating TD, you need to make sure that data transfer on a mobile network is included.

The next sequence of actions was carried out using the example of the LG smartphone with the Android 5 version.0:

  • Find the settings shortcut in the menu, enter them and select a item with networks;
  • Next, select “Modems and Network”. creating an access point;
  • Click “Create”;
  • Assign all parameters to compulsory fields: name when searching, protocols of protection and encryption;
  • Set the password from 8 characters long;
  • Determine the number of devices that can be connected to the network;
  • When everything is finished, you can go back and activate the point.

Important! To enable data transfer on a mobile network, you need to go to the settings (parameters), select the wireless networks and go to the mobile Internet (data).

On the system of the earliest versions, you can configure as follows:

  • Go from menu to parameters. wireless networks;
  • Scroll down and press “more”;
  • Find the “modem mode” or “access point”;
  • Execute all points from the previous instruction.

Creation occurs once. After that, the icon will appear on the notification panel, and you can turn on the point by activating the slider in the settings of network connections.

Using applications

In addition to standard Android tools, there are many programs to organize an access point. The most popular are: MypublicWifi, MhotSpot, Osmino and others. On the example of the last program, the setting instructions will be presented below below.

First you need to download and “put” the application from official sources: off.site or Play Market’a. After that, you need to open it, set the network parameters and “distribute” it. After these actions, the phone will go to the modem mode. To disable Hotspot, you need to go to the application and complete the distribution of traffic. Everything is done easier than in the standard settings of the phone, but there is one “but”: if in the latter it is set wrong or the application cannot access them to change, then the point will not create.

Reasons for the lack of Internet in Hotspot mode

Having done everything right, a person can still encounter difficulties that consist in the moments related to:

  • blocking the network with antiviruses and fuel sections;
  • impact on the system and its virus parameters;
  • errors in the operation of the operating system.

Antivirus programs that protect the device in real time often block all the connections to the network. Before creating and turning on the TD, you should configure or turn off the firewall in the same settings.

Viruses can get into the device with applications, the installation of which was not made from official sources. To eliminate their antivirus, on the contrary, you should turn on and check the system with simple scanning. If this does not help, then you can install a more “strong” program.

Important! You can track the viral program yourself. To do this, you need to go to the application dispatcher (tasks) and find out what unsystematic software has the rights to control network connections, delete it. After that, turn on the device again and check the connection.

Another option is possible to reset all the settings of the phone to factory. For this you need:

Turning on the access point on the smartphone

The setting of the router occurs after the access point is activated on the mobile device, so first you need to complete this task. To do this, on the smartphone C android, make the following:

Each device on Android or iOS has its own features to include an Internet access point, and there are also alternative methods of organizing such a transmission. If you have problems with this operation or you are looking for alternative options for its implementation, read other thematic articles on our website on the following links.

Router configuration

We move on to the complex part of the task under consideration, which consists in setting up the router. All actions are carried out in a web-integse, therefore, regardless of the model of network equipment, first of all, fulfill the authorization in this menu, which is more detailed

We will analyze the settings process itself on the example of three different manufacturers models, so that each user has a complete picture of what needs to be done in a web-integer.

TP-Link

TP-Link is one of the largest manufacturers of routers, the devices from which many users are purchased when connecting the Internet, so first we will consider this particular version of the web-intake. Connecting to an existing access point occurs without any problems.

To return the router to its original state, you will need to return the standard operating mode in the same fast settings menu and set the WAN parameters to obtain a network from the provider.

D-Link

The appearance of the D-LINK web-intake can be considered typical, since in many other manufacturers it is realized almost the same, but with small changes. The instructions below will help owners of other models to understand the setting.

Zyxel Keenetic

In conclusion, we will analyze the most unstable option, the need to fulfill the owners of the Zyxel Keenetic routers. In this case, the connection occurs through the WDS mode activated in the router settings.

You will find additional information on further actions in a similar article about TP-Link, but at the same time skip the process of interaction with the main device, since it is a smartphone, where the parameters are originally set correctly.

Wi-Fi point

You will need a router to organize a house of Wi-Fi access point. A router is a device that will coordinate the signals on the wired Internet and wireless signals in the radio channels that come from or to our devices. When buying, you need a Wi-Fi router, and not a router a router that can be used to branch the Ethernet wired network.

The wired Internet can provide a high speed than the Wi-Fi network, so when buying a router, you need to look at the speed that it can maintain (the passport may be called “Route speed”). There are several Wi-Fi network standards, they differ in data transfer speeds. Real speeds are always lower than the most possible for each standard by about 2 times. But even with such a decrease, the real speed can reach dozens of Mbps, which is quite enough for the normal operation of several connected consumers. The USB connector will also be used in the router, which can be used to connect to the home network of printers, scanners, etc. Printers that support Wi-Fi can be connected as other devices via a wireless network. But if there is no such support, then here is a USB connection and will help you in organizing a home network with a printer and other devices.

Many firms today produce network equipment, including routers. Therefore, what will you choose from. There will be several connectors in any Wi-Fi router. One of them is WAN, this entrance serves to connect an incoming Internet cable. There may also be several LAN connectors to connect other devices via cable. This is when a router can act as a router. Can be a USB port. And connector for connecting a power supply. There should also be the “VKL/Off” buttons of power and “Reset” to return to the factory installations.

Roter setup

After buying and unpacking the router, it needs to be connected for configuration. In the WAN connector we connect the input of the Internet, and to the LAN output for connecting a computer.

After that, we turn on the router, and insert the disk that goes with the router into the computer, and install all the necessary drivers and programs. There may also be a program on the disk with which you can perform all the settings of the router. But you can make these settings through the browser.

In order to go into the router settings through the browser, you must enter a address line address, which is written on the sticker on the bottom of the router. There should be an IP address of 4 groups of numbers (for example, this type: 192.168.one.one). There is also a login and password for access to the admin part of the router settings.

IP address, login and password for entering the settings

If this information is not indicated on the router and it is not in the instructions, then you can go on the computer on the way “Starting the control panel network and the Internet control center of networks and total access” and in the window opened, select “Change of Adapter Parameters”. And already here you should see the item “Connection on the local network”.

Here, clicking on it 2 times, you will get in the network of the network of the network.

By clicking on “Information” you will open a window with different information, but you need two lines.

This will be the IP address of the router and its value and enter into the address bar of the browser. You will be asked to enter a login and password. By default, this is the login “admin” and the password “admin”. If everything is correct, then a window with information about the network will open in the browser.

  • Create an Internet connection
  • Create access to a local network
  • Set the safety (change the entrance password to the admin part)

We connect a router to the Internet

First we enter the WAN section, there you will set up an Internet connection.

There you can configure several types of connection depending on the conditions of the provider. Set “Dynamic IP Address”. Most providers give users the dynamic address.

After that, click “apply”, the page with the settings should restart (this router is rebooted). After that, the computer should already be connected to the Internet.

If you choose pppoe. Also a common option, in this version, the provider is given to you a login and password, can also give out the addresses of the DNS servers and other additional settings. Additional settings depend on the provider. This is mainly only a login and password. That is, select PPPOE, enter the login and password from the provider, click “Apply” and the computer from which the settings are made will be connected to the Internet.

If you need to select the L2TP connection as a WAN (all these points depend on the provider), then in addition to the login and password you need to enter the server name. In addition, additional information may be required. All this information is issued by the provider and does not depend on the brand of the router.

Wireless Access Point vs Wi-Fi Router

wi-fi, router, access, point, change, standard

There may be a “static IP” for connecting WAN. In this case, you need to enter an IP address, subnet mask, gateway and possibly DNS address.

Additional data when choosing “static IP”

All considered options are possible if you have all the necessary information from providers. And if you do not know this data? Then they can be seen in the computer. How to do it see here.

After the introduction of all the data in the Wan Settings window, you click “Apply”, the router is rebooted.

Additional router settings

After that, you are part of the “Wireless Network” section.

At the “SSID” point you set the name of your network, which will be displayed in the list of wireless networks available for connection.

Next, select the type of encryption in the paragraph “Read Checking Method”. It is recommended to select “WPA Personal”.

Install the “Preliminary Key WPA”. which will be a password for entering the network. This password is needed to protect your Wi-Fi connection from the penetration of strangers. After all, the Wi-Fi network can also apply to other apartments in the radius of the coating specified in the passport.

After these settings, the router should already distribute Wi-Fi Internet.

If you need to change the login and password to enter the admin part, then you need to enter the “additional settings”. Further in the “Administration” section, look for the item “System”.

After entering the System section, changes in the login and password will be available to you.

After that, click “Apply” once again and the router will restart.

You also need to configure the security of connecting to the network and your router is ready to work on Wi-Fi distribution at your house.