TP-Link router does not connect to the Internet

The router does not distribute the Internet via Wi-Fi and the cable-the causes and methods of solving on a smartphone, computer or laptop

When users say that the router does not give out the Internet, it is important to understand the essence of the problem. Indeed, in practice, problems with distributing a wireless signal can be different: the router turns on and at first glance works properly, but there is no Wi-Fi, or there are a network and even other devices are found, but the Internet does not load it.

Often, problems with the distribution of the Internet arise at the stage of settings of the router. You brought it home, seemed to have set it up, but the pages of resources on the network are not loaded. At the same time, they may not open in different ways: either an error appears on the computer indicating the lack of access to the network, or the page does not load and the white screen flaunts before the eyes of the user. Such situations indicate the need to check the router and network settings. It is worth considering the problem with the slope of the routers from TP-Link, ASUS, KEENETIC-devices from these companies are most common today among users.

The router does not connect to the Internet, which is why Wi-Fi does not work on a computer

Often, the cause of errors with the inaccessibility of the Internet via Wi-Fi is the incorrect setting of the router to connect to the provider. A characteristic feature of the wrong network parameters will be an exclamation mark on the yellow background in the Windows panel next to the Internet icon. Plus, the text “limited” will be displayed in Windows 8 or 10, and in the connection status “without access to the Internet”.

TP-LINK Router Internet Connection & Wi-Fi Network Full Setup (PPPoE / Static)

If there is an Internet when installing a cable on a WAN port on a computer, but Wi-Fi does not work, then the problem is not with the connection itself, but in the configuration of the network in the settings of the router. To fix it, first of all, I recommend that you complete the full dropping of the router to the factory state. Most likely, a simple reboot will not help here, although you can try and just turn off the outlet router for a few seconds.

After reset by default, the router will begin to distribute a Wi-Fi signal. And you can even give up to it using SSID and password from the sticker on the case, but the network without access to the Internet.

This is logical. Wi-Fi is just needed for the primary setup of the router and the Internet, access to which the computer, laptop or smartphone has no yet. The wireless network indicator on the router will burn green, and the Internet light (WAN) will be red or orange.

Over, if you take out the cable and insert it back into the computer, then the Internet will appear on it. After all, the computer was previously connected to it, which means that the settings were still preserved.

In general, it is now necessary to go to the route administration panel and re.Enter all the parameters from the Internet.

tp-link, router, does, connect, internet

Forced Internet access restriction

Manual purpose IP addresses

If you connect to the Internet in the office or other public space, then you cannot exclude the use of additional settings on the router that limit the Internet access for users.

See also  How to turn on Internet sharing on your iPhone

One of the filtration methods is the manual purpose of IP addresses for computers. In normal mode, the router automatically distributes IP to all connecting devices through the so.Called DHCP server. But it can be disconnected in the settings. And the addresses manually are prescribed by the network administrator for each client.

If you have access to the router, then you need to register for your computer, laptop or smartphone IP address manually. Or turn on the DHCP server

If there is no password from the router, then contact the system administrator to add you to the number of users.

Guest network and customer filters

Also, so that everyone who gets on the Internet does not go on the Internet, several different stages of access to content can be configured through the router. For example, a guest network without access to the Internet or with an allowed access to a network only for certain users.

Also in some models it is possible to give out the world network only for manually registered devices. And for all new ones connected to Wi-Fi, limit the Internet.

For this, “parental control” or filtering by MAC addresses is often used. It can be tuned in such a way that the Internet access is allowed only to devices that are in a pre.Compiled “White List”.

It is necessary to add your computer to it or ask this to do a person responsible for the operation of the local network in your office.

Wired connection

The main method of connecting the router to a personal computer is to use the local network wire. To perform this task, the user will need to carry out only a few simple manipulations. Before starting, we clarify that the first steps of this method are mandatory in any case, so we will not duplicate them when considering the next.

tp-link, router, does, connect, internet

    Screw the box with a router, find the power cable there and pay attention to the rear panel of the equipment where all existing connectors are displayed. Here you need to find a port marked “Power”, which corresponds to the connector of the selected cable. Connect to the router with one side, and stick the second into the outlet.

Often, with this type of connection, there is no need to perform other actions, but there are situations when the Internet is absent for some reason. Then you should once again check the indicators, as well as the parameters of the operating system, which is more detail

Blog about modems, routers and GPON ONT terminals.

Simple home-made Wi-Fi Wi-Fi Wireless Route is a multifunctional device that is actually independent of the computer operating system. In the case of any problems that arise during his work, an ordinary average user may face the fact that he will not be able to find out why access to the Internet through the router disappears at least which side to look for the cause of the problem. Roofing felts is a failure at the provider, roofing felts is stupid and does not give access the router itself. In fact, there are several simple actions that are available to the user with almost any level of computer literacy.

Reload the router and computer. Yes, yes, this simple action allows you to return access to the Internet in 90% of cases. The fact is that the router is the same computer on which the Unix-like operating system is installed. And just like a computer, it can fail and buggy. For example, I had a D-Link ADSL modem, which stable once every 3-4 days I hung and helped the reboot helped. Since time, of course, a more fresh firmware has come out and the problem was eliminated. But until this point, everything was treated precisely precisely.

Look at the indicators (bulbs on the case). You should burn several indicators-power, WAN-connection or Internet and Wi-Fi network:

If there is a computer or laptop connected via Ethernet Cabble (LAN indicator). If so. Go to step 3.

The way out is most often one. Carry to the service or buy a new.

tp-link, router, does, connect, internet

See also  How to connect otg to your phone

TPLINK WIFI Router Configuration | Setup any TP-LINK Router Using Phone

-The WAN-connection indicator does not burn. It is usually marked as “WAN” or “Internet”. If you have an ADSL modem, then this is the DSL indicator, if you are connected through an optical ONT terminal, then it can be called Pon or Link there.

Disconnect the incoming cable from the connector on the router and turn on again. When connecting via ADSL. Check just in case the connecting on the splitter, in the case of GPON. Check the optical outlet if you have this installed. If it did not help, call the technical support of the provider, since damage is most likely on the line or on the equipment of the provider.

Check the settings.

To do this, you need to go to the web-integer (IP address usually 192.168.One.1 or 192.168.0.1) and see what is configured in the section “Internet” or “WAN”. Samo-Council you should know the parameters of your Internet connection. In which case. They can be clarified in the technical support of the provider.

NOTE: First line of technical support for the provider, they are very fond of advising subscribers to reset the router configuration using the Reset button. Take a hurry to do this, since you will completely “dive” it with this and you will have to register everything again or call a specialist for this and pay money. It is better to prepare first first. Check “from and to” all the necessary parameters and find the instructions for your model. And only then proceed to active actions.

If nothing suspicious is identified and all the parameters are set correctly, go to step 4.

Check the connected devices. You need to make sure that the Internet through the router disappears on all connected customers. To do this, they must be on the network at the same time. As soon as access to the Internet disappears on one of them. Immediately check its absence on the rest:

If it does not help, it seems that you have problems with the network board on PC. Check what IP parameters are spelled out in the properties of the TCP/IPV4 Internet protocol. You may have to update or reinstall the driver. If access is recovered, then the previous port was configured for another service. For example, IPTV.

-There is an Internet through the cable, via wi-fi-no. In this situation, you need to check the Wi-Fi settings on the router. Very often the reason is that wireless customers cannot get an IP address or address of DNS servers. Try to prescribe them manually. Sometimes the reason may be an incorrect grouping of ports. For example, you set up IPTV and added a wireless network to this group.

If you have a laptop, or a stationary computer is standing next to the router, then you can try to disconnect the cable of the provider that comes to your apartment, connect it directly to the computer’s network board, configure the connection and try to go to the Internet. If this successfully succeeded, then here you need to look for a problem in your router and understand why it does not give access. But if it doesn’t work directly, most likely the provider has problems. The only reservation, this verification method is suitable only if the fttb is connected (etth). If you have an optics GPON or the good old ADSL, then it will not work and you have to call technical support for calling the monster.

Problems in receiving IP addresses

The entire catch may be as follows: PC is difficult to get IP addresses. Often a certain address has already been set on it, or the automatic determination of the network settings is simply disabled. Is it so, will show identification. What is it?

Your router, when it works as usual, should be the main router of the local network. This suggests that its built-in DHCP server is active and assigns IP address to all devices. So, it may turn out that this server is inactive.

To find out all this, we must go to the settings. By clicking with the right mouse button, you will get into the “Networks and General Access Management Center”. Next, we do this:

  • Select “Changing the parameters of the adapter”;
  • We pay attention to the “Ethernet” or “Local network connection” icon. With a cable turned off or problems with it, a red cross will appear under the icon with the image of computers;
  • We achieve that the cross disappears, which means that the cable is connected;
  • Click on the field with the right button and find the “properties” in the falling menu;
  • We highlight the “IP version 4 (TCP/IPV4)” field, click on the “properties”;
  • In the new window, we note “get IP.Adures automatically”.
See also  How to connect headphones to a Windows 10 computer

It remains to click in this window “OK” and restart PC. Internet distribution problems are resolved.

Rotant Roter Restore TP-Link

TP-Link routers are designed for many years of continuous work and usually justify the good reputation of their manufacturer. Of course, if there was a breakdown of the hardware of the device, then you can either contact the repair specialists or buy a new router. But do not immediately panic and run to the store. It is possible that the malfunction is eliminated independently. Let’s try to make out the algorithm of actions to restore the performance of the router TP-LINK together.

If access to the local network and the Internet disappeared on devices connected to your router wirelessly, then it is primarily advisable to check the status of the Wi-Fi module on a computer, laptop or smartphone. It is possible that you accidentally turned off and forgot to turn on this function on your device.

We eliminate the problem

Namely, starting from specific conditions, you need to choose a way of solving the problem. Everything that will be described here is suitable for the following models of TP-Link: TL-WR741N, TL-WR841N, TL-WR1043ND and so on.

tp-link, router, does, connect, internet

The name of the network

Many buy the same models of the device and when they create an access point, its name is not changed. From here comes confusion and you cannot find your network, thinking that it is not at all. In this case, turn on the search for networks, for example, on the phone, then turn off the Wi Fai distributor and see which network will disappear, that was your.

Incorrect work of the router

As an option, you can drop the router settings or restart it, but it is better to start from the second, if it does not help, then already drop it. For rebooting, just pull the cord from the outlet and insert it back, and to reset the settings, on the back of the device there is a special button. Then double.Check whether there is the Internet or not.

The router is turned off

You need to check, perhaps you did not turn on the router at all, so the TP-Link Wi-Fi Wi-Fi does not work, and if it is included in the outlet, but the power indicator does not burn, then you should click on the ON/OFF button, it can also be found on back side of the router, where wires are connected.

Wi-Fi network is disabled

Another reason due to which the Internet distributor does not give out the network. It has a small button that turns on/disables Wi-Fi distribution, press it.

A wi-fi icon or an inscription will be drawn near it.

Route settings

What to do if Wi-Fi TP-Link has stopped working? Sometimes, the reason lies in the wrong settings to check them, enter in the address bar of browser 192.168.One.1 or 192.168.0.1 and click Enter.

You will be on the entrance page. Indicate the login and password. Admin admin.

We are interested in the section “Wireless mode”, which can be found in the menu on the left.

Open it and check to stood ticks, like on the screenshot.